Venus orbit around the Sun is an ellipse inside the Earth orbit. The elements of Venus orbit and its position are affected by the gravitational force of near planets therefore the elements were determined with Julian date through ten years 2011-2020. The orbital elements used to calculate Venus distance from the Sun, the heliocentric and geocentric equatorial coordinates. From the results the orbit of Venus and its position were described and show the gravity effect of near planets on it. The results get the values and their variation through ten years for the eccentricity, semi-major axis, inclination, longitude of ascending node, argument of perihelion, mean anomaly and distance from the Sun. The variation is very small through 10 years. The values of eccentricity variation are from 0.0067678 to 0.0067630 and inclination from 3º.39537 to 3º.39529 and argument of perihelion from 54º.634 to 54º.663 and longitude of ascending node from 76º.927 to 76º.899 and the mean anomaly increases at a uniform rate from 0º to 360º every one orbital period which mean value equal to 224.73 days. All variations were calculated through about 16 orbital periods and they are secular variation and may show more value through many hundred years due to perturbation from the Sun and planets especially the Earth, Mercury and Jupiter. The equatorial coordinates show that Venus has apparent retrograde motion as seen from Earth and that is because the Earth and Venus orbital periods around the Sun are different as well as the Venus orbit inside the Earth orbit. The distance between the Sun and Venus is various between minimum value 0.71843 AU and maximum value 0.72822 AU.
Cobalt substituted nickel copper ferrite samples with general formula Ni0.95-xCoxCu0.05Fe2O4, where (x= 0.00, 0.01, 0.02, 0.03, 0.04 and 0.05) were prepared by solid-state reactions method at 1373 K for 4h. The samples prepared were examined by X-ray diffraction (XRD(, atomic force microscope (AFM), Fourier transform infra-red spectroscopy (FTIR) and Vickers hardness. X-ray diffraction patterns confirm the formation of a single phase of cubic spinel structure in all the prepared samples . XRD analysis showed that the increase in the cobalt concentration causes an increase in the lattice constant, bulk density (ρm) and the x-ray density (ρx), whereas porosity (p) and crystallite size (D) decrease. The Topography of the surface observed
... Show More
(1)
EP/ metal composites were prepared as adhesives between two steel rods. Epoxy resin (EP) was used as a matrix with metal as fillers (Al, Cu, Fe,).
The preparation method for tensile adhesion tests includes two steel rods with adhesive composites between the rods to measure adhesion strength Sad and adhesion toughness Gad.
Results of tensile adhesion tests show that EP/ metals composite have maximum strength Sad for certain weight percentage of metals 2.95 and 9MPa at 10% for EP/Al and EP/Cu composite and 8.2MPa at 40% for EP/Fe composites
The electrical properties of the AlNiCo thin films with thickness (1000oA) deposited on glass substrates using Ion – Beam sputtering (IBS) technique under vacuum <10-6 torr have been studied . Also it studied the effect of annealing temperature from this films , It is found that the effective energy decrease with increase of temperature and the conductivity decrease with increase temperature 323oK but after this degree the conductivity increasing .
Recently, a great rise in the population and fast manufacturing processes were noticed. These processes release significant magnitudes of waste. These wastes occupied a notable ground region, generating big issues for the earth and the environment. To enhance the geotechnical properties of fine-grained soil, a sequence of research projects in the lab were conducted to analyze the impacts of adding sludge waste (SW). The tests were done on both natural and mixed soil with SW at various proportions (2%, 4%, 6%, 8%, and 10%) based on the dry mass of the soil used. The experiments conducted focused on consistency, compaction, and shear strength. With the addition of 10% of SW, the values of LL and PI decreased by 29.7% and 3
... Show More
(1)
Additive aluminum powder to the polystyrene to prepare the composites Polystyrene– Aluminum.The samples were prepared by using mechanical compressed method at low pressure and a temperature 120°C. Measurements of absorbance and reflectance spectra were carried out by UV-Visible spectrophotometer , the effect of additive aluminum on the optical band gap Eop and optical constants ( refractive index n, extinction coefficient k ,dielectric constant ε and optical conductivity σop) were studied for the prepared composites . Results showed a decrease in the Eop with increasing perc
... Show MoreThe interest in the issue of capital movement as an economic phenomenon has increased because of its effects and effects and its ability to influence the economic balance and the effectiveness of monetary policy. All countries seek to attract capital and benefit from it because of its effects and results such as supporting economic development process and optimal allocation of economic resources. The problem of the financing gap that most countries suffer from, and others, but sometimes the movement of capital creates challenges for monetary policy makers in achieving their goals.
After 2003, the Iraqi economy witnessed an openness and economic liberalization unlike previous years, which
... Show More
Mechanical and thermal properties of composites, consisted of unsaturated polyester resin, reinforced by different kinds of natural materials (Orange peels and Date seeds) and industrial materials (carbon and silica) with particle size 98 µm were studied. Various weight ratios, 5, 10, and 15 wt. % of natural and industrial materials have been infused into polyester. Tensile, three-point bending and thermal conductivity tests were conducted for the unfilled polyester, natural and industrial composite to identify the weight ratio effect on the properties of materials. The results indicated that when the weight ratio for polyester with date seeds increased from 10% to 15%, the maximum Young’s modulus decreased by 54%. When the weight rat
... Show More
Gestational diabetes mellitus (GDM) is a growing health concern that usually appears during the second and third trimester stage of pregnancy and is characterized by carbohydrate intolerance of variable severity. The aim of the present study was to scrutinize the relationship between the G972R polymorphism of the insulin receptor substrate-1 (IRS-1) gene with GDM in the Iraqi female population. One hundred and twenty of blood samples taken from healthy women (control) and women with gestational diabetes mellitus in 3rd trimester stage of pregnancy, fasting blood glucose (FBG) and HbA1c% measured to diagnose GDM, lipid profile (cholesterol, triglyceride, HDL, LDL, and VLDL), insulin concentration, insulin resistance and beta ce
... Show MoreGestational diabetes mellitus (GDM) is a growing health concern that usually appears during the second and third trimester stage of pregnancy and is characterized by carbohydrate intolerance of variable severity. The aim of the present study was to scrutinize the relationship between the G972R polymorphism of the insulin receptor substrate-1 (IRS-1) gene with GDM in the Iraqi female population. One hundred and twenty of blood samples taken from healthy women (control) and women with gestational diabetes mellitus in 3rd trimester stage of pregnancy, fasting blood glucose (FBG) and HbA1c% measured to diagnose GDM, lipid profile (cholesterol, triglyceride, HDL, LDL, and VLDL), insulin concentration, insulin resistance and beta cell function to
... Show More
(5)
(2)
