Al- Masab AL-Aam canal (or the Main Drain) is a vital strategic project in Iraq. It collects the drain water from the agricultural lands and drains to the Arabian Gulf via Shatt Al-Basra. Fifteen water samples were collected from different sites along the course of the Al- Masab Al-Aam canal southern sector extending from Nasiriyah Basra to evaluate the hydrochemical properties. The variation of the sediment’s texture along the southern sector was investigated. The results reflected that the sediment is characterized by the presence of sand, silt, and clay. It is noted that the amount of salt in the water increases during the summer when temperatures are rising, and consequently, the evaporation rate increases. Changes in the saturation index also continuously affect the dissolution and precipitation of minerals along the river. The results of the saturation index analysis showed that the relationship between sulfate concentration and mineral saturation coefficients tends to increase their solubility for most minerals. The importance of the research lies in knowing and identifying the factors causing the change in water quality through studying the hydrological and hydrochemical properties of water and comparing the results to find out the reasons for the increase and decrease in its concentrations along the study area.
In this research, we studied the effect of concentration carriers on the efficiency of the N749-TiO2 heterogeneous solar cell based on quantum electron transfer theory using a donor-acceptor scenario. The photoelectric properties of the N749-TiO2 interfaces in dye sensitized solar cells DSSCs are calculated using the J-V curves. For the 〖(CH_3)〗_3 COH solvent, the N749-TiO2 heterogeneous solar cell shows that the concentration carrier together with the strength coupling are the main factors affecting the current density, fill factor and efficiency. The current density and current increase as the concentration increases and the strength coupling increases as the N749-TiO2 heterogeneous in solar cell. However, the efficiency is more sens
... Show MoreThis paper studies the effect of the solar indices (total sunspot no., solar wind density and coronal mass ejection linear speed) on F2- layer electron density, as well as, the comparison of seasonal variations of electron density of F2- layer, NmF2, for Mars at local noontime and for maximum and minimum solar cycles.
Results show that there is an inverse correlation between sunspot number, solar wind density, CME linear speed and ionosphere electron density for Mars, at maximum and minimum solar cycles. This correlation is clear when electron density is at minimum value.
... Show MoreAbstract : A research was conducted to study the process parameters affecting hexavalent chromium Cr (VI) (carcinogenic compound) the removal percentage from the electrical industries company waste water that contain 88 mg/l of Cr (VI) concentration by adsorption onto tea wastes. Synthetic water with 88 mg/l Cr (VI) concentration was used. Several operation parameters affecting Cr (VI) removal efficiency were investigated, such as pH, initial Cr (VI) concentration, stirring time and tea wastes dose. The experimental results reveal that maximum Cr (VI) removal reached up to 94.26% at pH of 2, stirring time of 180 minute, tea wastes do
... Show MoreHygienic engineering has dedicated a lot of time and energy to studying water filtration because of how important it is to human health. Thorough familiarity with the filtration process is essential for the design engineer to keep up with and profit from advances in filtering technology and equipment as the properties of raw water continue to change. Because it removes sediment, chemicals, odors, and microbes, filtration is an integral part of the water purification process. The most popular technique for treating surface water for municipal water supply is considered fast sand filtration, which can be achieved using either gravity or pressure sand filters. Predicting the performance of units in water treatment plants is a basic pri
... Show MoreHygienic engineering has dedicated a lot of time and energy to studying water filtration because of how important it is to human health. Thorough familiarity with the filtration process is essential for the design engineer to keep up with and profit from advances in filtering technology and equipment as the properties of raw water continue to change. Because it removes sediment, chemicals, odors, and microbes, filtration is an integral part of the water purification process. The most popular technique for treating surface water for municipal water supply is considered fast sand filtration, which can be achieved using either gravity or pressure sand filters. Predicting the performance of units in water treatment plants is
... Show MoreThe current study aims to identify the needs in the stories of the Brothers Grimm. The research sample consisted of (3) stories, namely: 1- The story of the Thorn Rose (Sleeping Beauty) 2- The story of Snow White 3- The story of Little Red Riding Hood. The number of pages analyzed reached (15.5) pages, and to achieve the research objectives, Murray's classification of needs was adopted, which contains (36) basic needs that are further divided into (129) sub-needs. The idea was adopted as a unit of analysis and repetition as a unit of enumeration, Reliability was extracted in two ways: 1- Agreement between the researcher and himself over time, where the agreement coefficient reached 97%. The second was agreement between the researcher and tw
... Show MoreA study of the hadiths of supplication orchestration
In this work, we apply the notion of a filter of a KU-Algebra and investigate several properties. The paper defined some filters such as strong filter, n-fold filter and P-filter and discussed a few theorems and examples.
In this research, damping properties for composite materials were evaluated using logarithmic decrement method to study the effect of reinforcements on the damping ratio of the epoxy matrix. Three stages of composites were prepared in this research. The first stage included preparing binary blends of epoxy (EP) and different weight percentages of polysulfide rubber (PSR) (0%, 2.5%, 5%, 7.5% and 10%). It was found that the weight percentage 5% of polysulfide was the best percentage, which gives the best mechanical properties for the blend matrix. The advantage of this blend matrix is that; it mediates between the brittle properties of epoxy and the flexible properties of a blend matrix with the highest percentage of PSR. The second stage
... Show More