The interest in the issue of capital movement as an economic phenomenon has increased because of its effects and effects and its ability to influence the economic balance and the effectiveness of monetary policy. All countries seek to attract capital and benefit from it because of its effects and results such as supporting economic development process and optimal allocation of economic resources. The problem of the financing gap that most countries suffer from, and others, but sometimes the movement of capital creates challenges for monetary policy makers in achieving their goals.

   After 2003, the Iraqi economy witnessed an openness and economic liberalization unlike previous years, which

This paper presents an experimental and numerical study which was carried out to examine the influence of the size and the layout of the web openings on the load carrying capacity and the serviceability of reinforced concrete deep beams. Five full-scale simply supported reinforced concrete deep beams with two large web openings created in shear regions were tested up to failure. The shear span to overall depth ratio was (1.1). Square openings were located symmetrically relative to the midspan section either at the midpoint or at the interior boundaries of the shear span. Two different side dimensions for the square openings were considered, mainly, (200) mm and (230) mm. The strength results proved that the shear capacity of the dee

The proximate composition, mineral contents and the effects of sodium sulphate salts on emulsion capacity (EC) and stability (ES) of mushroom species M_{1 –} Lentinus subnudus Berk, M_{2 –} Chlorophyllum molybditis, M_{3 –} Volvariella esculenta, M_{4 –} Coprinus tramentarius, M_{5 –} Pleurotus ostreatus Jacq, M_{6 –} Termitomyces microcarpus, and M_{7 –} Pleurotus pulmonarius obtained from Nigeria were investigated using standard methods for analyses.  The mean of some of the results is:  Crude protein:  9.1±0.15 -13.80±0.15%, Crude fibre: 4.15±0.02 – 7.08±0.59%, Na: 177±2.56 –

  In this work, nanostructured TiO2 thin films were grown by pulsed laser deposition (PLD) technique on glass substrates. TiO2 thin films then were annealed at 400-600 °C in air for a period of 2 hours. Effect of annealing on the structural and morphological were studied. Many growth parameters have been considered to specify the optimum conditions, namely substrate temperature (300 °C), oxygen pressure (10-2 Torr), laser fluence energy density (0.4 J/cm2), using double frequency Q-switching Nd:YAG laser beam (wavelength 532nm), repetition rate  (1-6 Hz) and the pulse duration of 10 ns. The results of the X-ray test show that all nanostructures tetragonal are polycrystalline. These results show that grain size increase fr

Sludge from stone-cutting (SSC) factories and stone mines cannot be used as decorative stones, stone powder, etc. These substances are left in the environment and cause environmental problems. This study aim is to produce artificial stone composite (ASC) using sludge from stone cutting factories, cement, unsaturated resin, water, silicon carbide nanoparticles (SiC-NPs), and nano-graphene oxide (NGO) as fillers. Nano graphene oxide has a hydrophobic plate structure that water is not absorbed due to the lack of surface tension on these plates. NGO has a significant effect on the properties of artificial stone due to its high specific surface area and low density in the composite. Its uniform distribution in ASC is very low due to its hydropho

The regions around the world need to perform their results based on the local geoid. However, each region has different ground topography based on the amount of gravity in this region. Nowadays, the recent global Earth's gravity model of 2008 is successfully used for different purposes in geosciences research. This research presents an overview of the preliminary evaluation results of the new Earth Gravitation Model (EGM08) in the middle of Iraq. For completeness, the evaluation tests were also performed for EGM96 by examining 31 stations distributed over four Iraqi provinces. The national orthometric heights were compared with the GPS /leveling data obtained from these stations. This study illustrated that the GPS /leveling based on EGM

The aim of this research is to study the effect of welded joint design (Butt joint and lap joint) on thejoint strength during tension and fatigue loading with different current of welding (40,50,60,70,80) ^per, and different type of wire welding. The result of this research is showed that the effect of fatigue loading on the type of joint is more than the effect of tension loading on it. And the butt joint welding is better than the lap joint welding during the fatigue loaded.The experimental results of the effect of W'elding current showed that more increasing and more decreasing the value of the heat input, during the welding was found to produce mechanical brittleness on the buttjoint welding during the static and dynamic loading. Also i

The phagocytic activity of peritoneal and blood cells counts with neutrophils and monocytes were evaluated in albino mice treated wtth two antigen preparations (A and B) from group A streptococci (GAS). Antigen A included water bathed bacteria at 70 °C for 60 minutes, while in Antigen B the bacteria was autoclaved at 121° C for 15 minutes. The animals were treated with 12 intraperitoneal doses of the antigens with intervals of three days (36 days). The 12th dose was a challenge dose (live bacteria). The first three doses of Antigen A increased the phagocytic index (PI) to a range of 76.46-78.69%, then a gradual decreased percentage was observed, especially at the challenge dose (PI=6.42%). The count of neutrophils and monocytes fol

The main objectives of this study were investigating the effects of the maximum size of coarse Attapulgite aggregate and micro steel fiber content on fresh and some mechanical properties of steel fibers reinforced lightweight self-compacting concrete (SFLWSCC). Two series of mixes were used depending on maximum aggregate size (12.5 and 19) mm, for each series three different steel fibers content were used (0.5 %, 1%, and 1.5%). To evaluate the fresh properties, tests of slump flow, T500 mm, V funnel time, and J ring were carried out. Tests of compressive strength, splitting tensile strength, flexural tensile strength, and calculated equilibrium density were done to evaluate mechanical properties. For reference mixes, the