This paper is carried out to detect the subsurface structures that have geological
and economical importance by interpreting the available reflection seismic data of
an area estimated to be about (740) km2. The Khashim Al-Ahmer structure is partial
of series structures of (Injana – Khashim Al-Ahmer – Mannsorya) from the (NW to
the SE), it is located within for deep faulted area. The component of the one
elongated dome of asymmetrical of structure which has(SW) limb more steeper than
the (NE) limb.Twenty three seismic sections had been interpreted for two seismic
surveys and the total length of all seismic lines is about (414.7) Km. Interpretation
of seismic data was focused on two reflectors (Fatha and Jeribi) Formations which
belong to Lower and Middle Miocene age. The reflectors were picked and identified
by tying them directly to well Khashim Al-Ahmer-2, the Lower Fars(Fatha
Formation) reflector was picked at TWT ranging from (0.3-1.7) sec while the Jeribi
reflector was picked at TWT ranging from (0.83- 2) sec. The depth map showed that
the depth of the Jeribi Formation ranges between (1100 - 2000) m, and the velocity
maps of studied reflector showed increase of velocity values to the south east and
there is a local closure in the north east of the study area and decrease to the north
west and the velocity values decrease and give closure situated below well KA-
2.The magnitude of velocity values ranges in Jeribi velocity map from (3100 to 3400
m/sec). Seismic attributes techniques (instantaneous phase) is important to detect the
hydrocarbon accumulation on seismic sections. Major faults (reverse and thrust)
were picked along study area on instantaneous phase sections. These faults extend in
NW-SE trend and the displacement of the fault ranges between (400-660) m. The
velocity, time and depth maps were drawn by the aid of GeoFrame and petrel
software.
The IGRF model is the empirical representation of the Earth magnetic field recommended for scientific use by the International Association of Geomagnetism and Aeronomy(IAGA).
Since the Geomagnetic field has the abi lity to change the orientation of satellite, the strength of Geomagnetic field and its horizontal component have been studied.
This paper discusses the phenomenon of the Geomagnetic field intensity and its horizontal component at diferent altitudes and at certain latitudes, the geomagnetic field data is obtained by using IGRF2000 model at Baghdad (44.7 degree East longitude) .
Background: The present study was carried out to compare shear bond strength of sapphire bracket bonded to zirconium surface after using different methods of surface conditioning and assessment of the adhesive remnant index. Materials and methods: The sample composed of 40 zirconium specimens divided into four groups; the first group was the control, the second group was conditioned by sandblast with aluminum oxide particle 50 μm, the third and fourth group was treated by (Nd: YAG) laser (1064nm)(0.888 Watt for 5 seconds) for the 1st laser group and (0.444 Watt for 10 seconds) for the 2nd laser group. All samples were coated by z-prime plus primer. A central incisor sapphire bracket was bonded to all samples with light cure adhesive res
... Show More
|
The mechanism of hydrogen (H2) gas sensor in the range of 50-200 ppm of RF-sputtered annealed zinc oxide (ZnO) and without annealing was studied. The X-ray Diffraction( XRD) results showed that the Zn metal was completely converted to ZnO with a polycrystalline structure. The I–V characteristics of the device (PT/ZnO/Pt) measured at room temperature before and after annealing at 450 oC for4h, from which a linear relationship has been observed. The sensors had a maximum response to H2 at 350 oC for annealing ZnO and showed stable behavior for detecting H2 gases in the range of 50 to 200 ppm. The annealed film exhibited hig |
(2)
Isotope tracer methods were used to determine flow paths, recharge areas, and relative age for groundwater in the Ameriyat Al- Falluja Al-Anbar governorate. The isotope of surface water and groundwater in the Ameriyat Al- Falluja area was assessed using a stable isotope technique. Data stable isotope parameters (2H and 18O) for three surface water and five groundwater samples were detected. The comparison of hydrogen and oxygen isotope compositions between groundwater and Euphrates River water demonstrated that the composition of the hydrogen and oxygen isotopes from Euphrates River matched that of the local meteoric water. This indicated that rainfall is the primary source of the river wate
... Show MoreThe interacting boson models, and were used to perform a complete study of even –even 160-168Yb isotopes .The low –lying positive parity states, dynamic symmetries, reduced electric quadrupole transition probability , quadruple momentum , and potential energy surface for 160-168Yb were investigated. Energy level sequences and energy ratios showed the gradual transition of the properties of these nuclei from the γ-unstable features to the rotational features . Adding the pairing parameter to Hamiltonian had a very slight effect on this feature, but it raised the β band, since it represents symmetry breaking such as in γ-unstable features . This applie
... Show More
(3)
(2)
Gas adsorption phenomenon on solid surface has been used as a mean in separation and purification of gas mixture depending on the difference in tendencies of each component in the gas mixture to be adsorbed on the solid surface according to its behaviour. This work concerns to study the possibilities to separate the gas mixture using adsorption-desorption phenomenon on activated carbon. The experimental results exhibit good separation factor at temperature of -40 .
The main objective of resources management is to supply and support the site operation with necessary resources in a way to achieve the required timing in handing over the work as well as to achieve the cost-realism within the budget estimated. The research aims to know the advantage of using GIS in management of resources as one of the new tools that keep pace with the evolution in various countries around the world also collect the vast amount of spatial data resources in one environment easily to handled and accessed quickly and this help to make the right decision regarding management of resources in various construction projects. The process of using GIS in the management and identification of resources is of extreme importance in t
... Show More
Electrical Discharge Machining (EDM) is a non-traditional cutting technique for metals removing which is relied upon the basic fact that negligible tool force is produced during the machining process. Also, electrical discharge machining is used in manufacturing very hard materials that are electrically conductive. Regarding the electrical discharge machining procedure, the most significant factor of the cutting parameter is the surface roughness (Ra). Conventional try and error method is time consuming as well as high cost. The purpose of the present research is to develop a mathematical model using response graph modeling (RGM). The impact of various parameters such as (current, pulsation on time and pulsation off time) are studied on
... Show More
(1)
Engineering project assessment at Al-Muthana Airport in Baghdad, Iraq, has been studied using a 3D electrical resistivity imaging survey. The site investigation is crucial for assessing the future of the region's infrastructures since it reveals the location of buried facilities or weak zones below the surface and measures localized groundwater levels. Wenner-Schlumberger array was used to conduct four parallel 2D electrical resistivity spreads (MU1 to MU4). Each spread line was 100 m in length with 1 m electrode spacing and an average spacing of 9 meters between any two adjacent lines. The depth of the investigation was around 23.8 m. Survey lines were drawn going from northwest to southeast. These spreads were combined to prov
... Show More