In this study, investigations of structural properties of n-type porous silicon prepared by laser assisted-electrochemical etching were demonstrated. The Photo- electrochemical Etching technique, (PEC) was used to produce porous silicon for n-type with orientation of (111). X-ray diffraction studies showed distinct variations between the fresh silicon surface and the synthesized porous silicon surfaces. Atomic force microscopy (AFM) analysis was used to study the morphology of porous silicon layer. AFM results showed that root mean square (RMS) of roughness and the grain size of porous silicon decreased as etching current density increased. The chemical bonding and structure were investigated by using fourier transformation infrared spectroscopy (FTIR). Porosity of the porous silicon layer and thickness were determined gravimetrically. Increasing the etching current density led to increase the surface porosity and thickness. Porosity between77% and 82% were observed for current densities between 24 mA/cm2 and 116 mA/cm2
A particular solution of the two and three dimensional unsteady state thermal or mass diffusion equation is obtained by introducing a combination of variables of the form,
η = (x+y) / √ct , and η = (x+y+z) / √ct, for two and three dimensional equations
respectively. And the corresponding solutions are,
θ (t,x,y) = θ0 erfc (x+y)/√8ct and θ( t,x,y,z) =θ0 erfc (x+y+z/√12ct)
A collection of pictures of traditional Kurdish women's national clothing and contemporary clothing was collected. A visit was also made to the city of Sulaymaniyah and the city of Halabja to find out the foundations of traditional clothing for the Kurdish regions and the impact of contemporary fashion on traditional dress. Which represents the culture and regionalism and reflects the picturesque nature of northern Iraq, and in order to complete the study, the parametric measurements of the clothes were analyzed and the graphs of the dress and its accessories were re-drawn to understand and make a comparison between them to study the clear influences and changes and examine the possibility of benefiting from them in sewing contemporary f
... Show MoreThe calibration of a low-speed wind tunnel (LSWT) test section had been made in the present work. The tunnel was designed and constructed at the Aerodynamics Lab. in the Mechanical Engineering Department/University of Baghdad. The test section design speed is 70 m/s. Frictional loses and uniformity of the flow inside the test section had been tested and calibrated based on the British standards for flow inside ducts and conduits. Pitot-static tube, boundary layer Pitot tube were the main instruments which were used in the present work to measure the flow characteristics with emphasize on the velocity uniformity and boundary layer growth along the walls of the test section. It is found that the maximum calibrated velocity for empty test s
... Show MoreResearch and Development Programs Effectiveness in the Central Library of Baghdad University
Background: Glucose-6 Phosphate Dehydrogenase (G6PD) Deficiency is one of the commonest inherited enzyme abnormalities in humans, caused by many mutations that reduce the stability of the enzyme and its level as red cells progress in age.
Objectives: To determine the useful hematologic indicators of hemolysis, observe an early detection of G6PD enzyme deficiency (if any), and the available therapeutic measures.
Patients and Methods: 123 patients with G6PD deficiency and hemolysis after exposure to fava beans whom visited AL-Elwiya Pediatric Teaching Hospital from the 1st of February 2016 till 31st of May 2016 were entered this study retrospectively. Hemolysis laboratory indicators were observed. Management supportive measures were
This research deals with shedding light on the issue of the poor understanding of students of Islamic sciences colleges for the subject of modern sciences; their causes and treatment, and it started with an introduction and an introductory research; The general weakness of the level of students of colleges of Islamic sciences in this article, and I detailed these reasons that relate to: the curriculum, the teaching staff, and students, and then concluded it with proposals and recommendations that would address this weakness.
The process for preparing activated carbon (AC) made from tea residue was described in this paper. Investigated were the physicochemical characteristics and adsorption efficiency of the produced AC. Activation with potassium hydroxide (KOH) and carbonization at 350 °C are the two key steps in the manufacturing of AC. The activated carbon was used to adsorb Tetracycline (TC). Different parameters were studied at room temperature to show their effects on the adsorption efficiency of TC. These parameters are the initial concentration of adsorbate TC, solution acidity pH, time of adsorption, and adsorbent dosage. The prepared active carbon was characterized using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (
... Show MoreFormulations based on nanomaterials have the ability to reduce the consuming of hazardous pesticides and theirimpact on human health and environment. The present study focused on a comparative investigation of histological effects of nanocapule acetamiprid (NACMP) in vivoand commercial parental bulk form of acetamiprid (ACMP) on albino mice. Nanoformulations of pesticides have the potential to improve food productivity without compromising with the ecosystem. In the present study, nanocapsules containing acetamiprid were prepared from two natural macromolecules, alginate and chitosan. The characterization of the nanocapsules were investigated by Dynamic Light Scattering(DLS), T ransmission Electron Microscopy (TEM) and Atomic force
... Show MoreThe field experiment was conducted with the aim of developing and testing an automatic sprayer for agricultural spray experiments and studying the effect of spray pressure, spray speed and spray height on the spraying process. The effects of the major spraying factors (pressure, speed, and height) on the spraying performance of the automatic sprayer were studied. This study included several traits: First - the drop sizes - Second - the penetration of the spray into the vegetation cover - Third, the spray wasted. The results showed: - First: - Increase in coverage percentage when using the first speed, 2 km / h, which amounted to 26.85%. An increment in the spraying penetration of the vegetation cover was observed at the second speed
... Show More