The biggest problem of structural materials for fusion reactor is the damage caused by the fusion product neutrons to the structural material. If this problem is overcomed, an important milestone will be left behind in fusion energy. One of the important problems of the structural material is that nuclei forming the structural material interacting with fusion neutrons are transmuted to stable or radioactive nuclei via (n, x) (x; alpha, proton, gamma etc.) reactions. In particular, the concentration of helium gas in the structural material increases through deuteron- tritium (D-T) and (n, α) reactions, and this increase significantly changes the microstructure and the properties of the structural materials. Therefore, in this study, the effects of the different nuclear level density models on the excitation functions of the (n, α) reactions on 46-50Ti isotopes, an attractive candidate for the structural material for fusion reactors, have been investigated for the first time. Also, the differential cross-sections with respect to alpha energy for the emission of alpha particles of the 46-50Ti (n, xα) reactions have been investigated at 14.1 MeV incident neutron energy. The calculations are performed using the two-component exciton model in the TALYS 1.9 code, and the results are compared with available experimental data. The results of this study will contribute to nuclear database as required for improving, design and operations of the important facilities as ITER (International Thermonuclear Experimental Reactor), DEMO (The demonstration power plant) and ENS (European Nuclear Society).
This research aims to identify the effect of numbered heads strategy on developing oral expression skills among fifth-grade primary students in Bisha Province. To achieve this, the researcher prepared a research tool represented in the observation card which consists of (27) statements distributed in four axes. The tool was sent to (5) experts in the field to verify their validity. In light of their corrections, the tool was developed to be valid for gathering field information. To verify the validity of the content and the reliability of the tool, the researcher applied it to a sample consists of (20) students from outside the research group. The overall coefficient of correlation between the statements of the tool is as follows: (.95,
... Show More230 stool samples were collected from 2 state homes for (males and females) to investigate
the infection of different intestinal parasites (pathogenic and non-pathogenic).
The infection rate was higher among males 15.7% than females 6%, these rates were
increased when concentration method was employed up to 54.8% for males and 8.7% for
females significantly.
Most infected orphans were found to harbor single parasite followed by double, triple
parasites.
The highest rate of infection was found among young age group (1-5) years old, while
the older age groups got lowest rates.
Of helminthes, the commonest parasite was Hymenolepis nana 5.7% and of protozoa, the
commonest intestinal parasite was Giardia lamblia
Fiber Bragg Grating has many advantages where it can be used as a temperature sensor, pressure sensor or even as a refractive index sensor. Designing each of this fiber Bragg grating sensors should include some requirements. Fiber Bragg grating refractive index sensor is a very important application. In order to increase the sensing ability of fiber Bragg gratings, many methods were followed. In our proposed work, the fiber Bragg grating was written in a D-shaped optical fiber by using a phase mask method with KrFexcimer. The resultant fiber Bragg grating has a high reflectivity 99.99% with a Bragg wavelength of 1551.2 nm as a best result obtained from a phase mask with a grating period of 1057 nm. In this work it was found that the rota
... Show MoreThis study investigated the shear performance of concrete beams with GFRP stirrups vs. traditional steel stirrups. Longitudinal glass fiber‐reinforced polymer (GFRP) bars were used to doubly reinforce the tested beams at both the top and bottom of their cross sections. To accomplish this, several stirrup spacings were provided. Eight beam specimens, measuring 300 × 250 × 2400 mm, were used in an experimental program to test under a two‐point concentrated load with an equal span‐to‐depth ratio until failure. Four beams in Group I have standard mild steel stirrups of 8 mm diameter, while four beams in Group II have GFRP stirrups with the same adopted diameter. The difference betwe
Pseudomonas aerogenosa lipopolysaccharidewas extracted by hot phenol method and purified by gel filtration method using the Sephadex G-200 gel and detected by the limulus amebocyt lysate (EU/ml 0.03)(Wako Chemicals USA, Inc.). The inhibitory effect of partially purified LPS on Candida glabrata yeast was studied in a microdilution method. This study found that LPS has an inhibitory effect on Candida glabrata with the lower concentrations. The inhibitory effect of LPS which treated with heating was studied under boiling and wet heat effect. The toxicity of LPS on Candida glabrata was not affected when treated with heating LPS and the results were similar to those found in untreated LPS
This study investigated the shear performance of concrete beams with GFRP stirrups vs. traditional steel stirrups. Longitudinal glass fiber‐reinforced polymer (GFRP) bars were used to doubly reinforce the tested beams at both the top and bottom of their cross sections. To accomplish this, several stirrup spacings were provided. Eight beam specimens, measuring 300 × 250 × 2400 mm, were used in an experimental program to test under a two‐point concentrated load with an equal span‐to‐depth ratio until failure. Four beams in Group I have standard mild steel stirrups of 8 mm diameter, while four beams in Group II have GFRP stirrups with the same adopted diameter. The difference betwe
In Incremental sheet metal forming process, one important step is to produce tool path, an
accurate tool path is one of the main challenge of incremental sheet metal forming
process. Various factors should be considered prior to generation of the tool path i.e.
mechanical properties of sheet metal, the holding mechanism, tool speed, feed rate and
tool size. In this work investigation studies have been carried out to find the different tool
path strategies to control the twist effect in the final product manufactured by single point
incremental sheet metal forming (SPIF), an adaptive tool path strategy was proposed and
examined for several Aluminum conical models. The comparison of the proposed tool path with t
Abstract:
If we neglect the value of historical fashions as a source of inspiration for
contemporary fashion designers we will neglect a treasure of original designs.
In neglecting such a treasure how could we then know what is original. Today
the most famous fashion designers are often inspired, in the outwardly from
and internal lines of their fashions, by fashion designed during the ages of the
past.
Designers can find such fashions in books of history and museums. But
the historical ages are not equal in the fertility of the originality and novelty of
their fashions. Thus the contemporary designer may not find the old designs
inspiring so he invents them.
The researcher was keen in this paper to inclu
Abstraction showed a case of distinction between art schools, in which reality was reduced using overlapping artistic elements and techniques to reach the artist's self-realization when abstracting the reality, and searching for implicit implications for the content of the artistic painting.
Building a system of relations and formulations between abstracting the reality of the physical forms and employing the symbols and codes to convey a message to the recipient who interacts with what he watches through the processes of explanation, interpretation, and linking the particles and reveal the pure aesthetics for the artwork.
Thus the current research deals with the following chapters and sections: the methodological framewo
... Show More