The current study showed that the plants were collected from 23 geographical locations in Brenaj, Wasit, Iraq. The region was characterized by a great diversity of wild plants spread densely in this region. The results were as follows: 32 families, 149 species. Asteraceae was the most widespread with 29 species from the group of dicotyledons, followed by the Fabaceae family (19) species, but there are 13 plant families, with one plant species recorded for each plant family. in Brenaj, Wasit included: Aizoaceae, Capparaceae, Convolvulaceae, Frankeniaceae, Molluginaceae, Papaveraceae, Phyllanthaceae, Primulaceae, Rutaceae, Rubiaceae, Verbenaceae, Zygophyllaceae, Urticaceae, while the plant family Poaceae was most widespread in genera and spec

This paper presents numerical and experimental stress analyses to evaluate the contact and bending stresses on the teeth of spiral bevel gear drive. Finite Element Method has been adopted as a numerical technique which accomplished basically by using ANSYS software package. The experimental stress analysis has been achieved by using a gear tooth model made of Castolite material which has photoelastic properties. The main goal of this research is detecting the maximum tooth stresses to avoid the severe areas that caused tooth failure and to increase the working life for this type of gear drives.

A field experiment was conducted at experimental field of Mechanization Agriculture , the
College of Agriculture , Abu – Ghraib , University of Baghdad .To measure transmitted vibration to
seat tractor during operation tillage , mold board plow with New Holland 66-S- 80 tractor as one
machinery unit , Soil was treated at soil constant moisture ( 18 – 20 % ) with two depths of plowing
(15 and 20 cm ) and three speed of tractor 2.0 , 3.5, 6.8 km / h . Three main dimensions in seat
tractor measurement vertical, longitudinal and lateral acceleration. Split plot design under
completes block design with three replicates

This study aims to numerically simulate the flow of the salt wedge by using computational fluid dynamics, CFD. The accuracy of the numerical simulation model was assessed against published laboratory data. Twelve CFD model runs were conducted under the same laboratory conditions. The results showed that the propagation of the salt wedge is inversely proportional to the applied freshwater discharge and the bed slope of the flume.  The maximum propagation is obtained at the lowest discharge value and the minimum slope of the flume. The comparison between the published laboratory results and numerical simulation shows a good agreement. The range of the relative error varies between 0 and 16% with an average of 2% and a roo

Recently new trends of mosques’ architecture have appeared. These trends differed from those of traditional ones in charictaristics which include two and three dimentional level. The traditional mosques' architecture are affected by several factors, so the research problem is (lack of knoweledge about factors forming traditional mosques' architecture and its effect on contemporary trends of mosques' architecture).The hypotheses of research is (the functional, aesthetic and symbolic religious factors of style are the most active factors in forming contemporary trends of mosques' architecture than religious and environmental factor).The research conclusion is that the symbolic functional factor is most effective factor i

Process capability provides a quantitative measure for gasoline production conformance to specifications.It was measured throughout four consecutive months of the last quarter of 2011. Results revealed high percentages (up to 44%) of non conforming gasoline blends to Iraqi marketing specifications for petroleum products (2000) by inspecting 122 different samples of Iraqi regular gasoline (RON 85).
Quality cost analysis as an important financial control tool was carried out to evaluate Cost of Quality (COQ) which was large due to non conforming gasoline reached up to (722.8 M.ID) in October. In this research COQ was investigated in order to identify the opportunities of gasoline quality improvements through production process. Also cus

Ease of transfer between different modes of public transportation within the stations is a significant contribution to the movement that can be provided by transportation industries to develop solutions of integrated transportation. It is future integrated multimodal transportation, to make public transportation more enjoyable and interesting, in addition to passenger transportation and future movement of goods are also depend on multimodal transportation The importance of interchange promotion between multimodal as a basic feature of passengers buildings in modern Railway Stations the Research problem:" con

The printed circuit heat exchanger is a plate type heat exchanger with a high performance and compact size. Heat exchangers such as this need a unique form of bonding and other techniques to be used in their construction. In this study, the process of joining plates, diffusion bonding, was performed and studied. A special furnace was manufactured for bonding purposes. The bonding process of copper metal was carried out under specific conditions of a high temperature up to 700 ^oC, high pressure of 3.45 MPa, and in an inert environment (Argon gas) to make tensile samples. The tensile samples are cylindrical shapes containing groves representing the flow channels in the printed circuit heat exchanger and checking their tensile st