The Neutron Fermi Age, t, and the neutron slowing down density, q (r, t) , have been measured for some materials such as Graphite and Iron by using gamma spectrometry system UCS-30 with NaI (Tl) detector. This technique was applied for Graphite and Iron materials by using Indium foils covered by Cadmium and the measurements done at the Indium resonance of 1.46 eV. These materials are exposed to a plane 241Am/Be neutron source with recent activity 38 mCi. The measurements of the Fermi Age were found to be t = 297 ± 21 cm2 for Graphite, t = 400 ± 28 cm2 for Iron. Neutron slowing down density was also calculated depending on the recent experimental t value and distance.
This study focused on the improvement of the quality of gasoline and enhancing its octane number by the reduction of n-paraffins using zeolite 5A. This study was made using batch and continuous mode. The parameters which affected the n-paraffin removal efficiency for each mode were studied. Temperature (30 and 40 ˚C) and mixing time up to 120 min for different amounts of zeolite ranging (10-60 g) were investigated in a batch mode. A maximum removal efficiency of 64% was obtained using 60 g of zeolite at 30 ˚C after a mixing time 120 min. The effect of feed flow rate (0.3-0.8 l/hr) and bed height (10-20 cm) were also studied in a continuous mode. The equilibrium isotherm study was made using different amounts of zeolite (2-20 g) and the
... Show MoreThis research concern to analyse and simulate the temperature distribution in the spot welding joints using tungsten arc welding shielded with inert gas (TIG Spot) for the aluminum-magnesium alloy type (5052-O).
The effect of and the quantity of the heat input that enter the weld zone has been investigated welding current, welding time and arc length on temperature distribution. The finite element method (by utilizing programme ANSYS 5.4) is presented the temperature distribution in a circular weld pool and the weld pool penetration (depth of welding) through the top sheet ,across the interface into the lower sheet forming a weld spot. &nbs
... Show MoreBackground: The possibility of converting the organic fraction of municipal solid waste to mature compost using the composting bin method was studied. Nine distinct treatments were created by combining municipal solid waste (MSW) with animal waste (3:1, 2:1), poultry manure (3:1, 2:1), mixed waste (2:1:1), agricultural waste (dry leaves), biocont (Trichoderm hazarium), and humic acid. Weekly monitoring of temperature, pH, EC, organic matter (OM percent), and the C/N ratio was performed, and macronutrients (N, P, K) were measured. Trace elements, including heavy metals (Cd and Pb), were tested in the first and final weeks of maturity. Results: Temperatures in the first days of composting reached the thermophilic phase in MSW compost
... Show MoreThe concept of sustainability is one of the modern concepts that influenced the quality of the urban plans for the cities, through the interest in the environmental and social aspects as well as the economic aspect and the need to balance to achieve sustainable development.
The research aims to identify the most prominent methods of sustainable urban land use planning and the strategies developed within these approaches to achieve sustainable development. The research started from the problem of a knowledge gap in adopting sustainable approaches and strategies when planning urban land uses for the holy city of Karbala.
In the theoretical aspect, the concepts of sustainable development, sustainable planning methodologies a
... Show MoreA study has been done to find the optimum separators pressures of separation stations. Stage separation of oil and gas is accomplished with a series of separators operating at sequentially reduced pressures. Liquid discharged from a higher pressure separator into the lower pressure separator. The set of working separators pressures which yield maximum recovery of liquid hydrocarbon from the well fluid is the optimum set of pressures which is the target of this work.
Computer model is used to find the optimum separators pressures. The model employs the Peng-Robinson equation of state for volatile oil. Application of this model shows good improvement of al
The study aimed to identification the effect of brainstorming in linguistically grow of garten child the sample of study is composed from (48)male and female children have been distributed for two groups,one of them is experimental and another is disciplined for every per of garten and pre education,and they have been awarded in a number of variations. For measuring the subordinate variation(linguistically grow)the researcher prepared ascale for this purpose that consist of two parts:the first part the scale of linguistically grow of garten child(4-5 years)and the second part the scale of linguistically grow of pre education child (5-6 years).Consist of every one from (20)shapes of linguistically grow shapes for garten chil
... Show Morewords of God the Quranic text , is genera words have many faces and connotations a ccording to references, cutures and Ages.That the Quranic text is fixed , But the connotations are moveable the scientists agreed about the miracle of the Qurantic text , But they differd of the Position of miracLe including the muatazala and Al- Ashaira who have adopted the idea of sytem and miracle of linguistic . Most of them were lingustics, grammerians and writers as: AL- Jahith, AL- Faraa Abivbeida , Ibn kutaba , AL -Rumani , AL -katabi , AL- Bakilaai , AL- Gargani and Others.
They also differed in what the words of Allaah mean . Is the Quranic text creature or updated ,it is the issue that exhausted the effort.of muslim scientists though its imbo
Rotating blades are the important parts in gas turbines. Hence, an accurate mathematical estimation (F.E.M) of the stresses and deformations characteristics was required in the design applications to avoid failure. In recent year’s there are researchers interest in the effect of temperature on solid bodies has greatly increased, The main of this study investigated the thermal and rotational effects. So, the thermal stresses due to high pressure and temperature are studies, also determine the steady state stresses and deformations of rotating blades due to mechanical effect. Many parameters such as thickness and centre of rotating are investigated in this paper. The
... Show More