Background: Sperm motility disorder is an important cause of infertility in male, and one of the causes of reduced motility of the sperm is the disorders of the mitochondria because it provides the required energy for sperm motility, Laser biostimulation or low-level laser therapy has a positive effect on the mitochondria and led to increasing the synthesis of ATP. Method: Twenty fresh human semen samples were used in this research study, each sample was separated into two portions, one was used as control which is not exposed to the laser beam and the other was irradiated with the wavelength of 410 nm diode laser with an output power of 100 mW and an exposure time of 60 seconds, then the measurement of the progressive motility, non-progressive motility, and the immotile sperm were assessed after 5,15,30 min of irradiation for every control and the irradiated samples. Results: the progressive and non-progressive motility of the sperm was significantly increased following irradiation compared to the control samples also the number of immotile sperm was significantly decreed after irradiation. Conclusion: We observed that a low-power laser of 410 nm wavelength could cause sperm motility to increase for a short time.
Background: The nasofrontal angle is the angle between the forehead & dorsum of the nose, it is of prime importance in giving the shape of the nose in relation to face. Workers studied this angle in living individuals, in this work, the angle was measured on dry human skulls, in addition, its value was statistically correlated with certain facial parameters.
Objectives: Determination of the value of nasofrontal angle in human skulls & correlation of this value to other facial parameters, namely; length of nasal bone, nasion height & midfacial length as these parameters are important for surgeons working in rhinoplasty.
Methods: The nasofrontal angle & other facial parameters were measured ca
(2)
The effect of laser radiation on human aorta, coronary, and pulmonary arteries, and pulmonary veins has been investigated. Xenon-Chloride (eximer), Nitrogen, and Nd-YAG pulsed lasers of wavelengths 308, 337, and 1060 nm respectively were used. Their effects on fresh postmortem tissues, normal and diseased, was studied. The diameter and depth of ablation of the exposed tissues, in air, were measured as a function of many factors related to the type of laser and nature of the tissue. The effect of properties of the applied lasers, such as average power density and deposited energy density, on the exposed tissue surface were studied. The increase of these two parameters cause an increase in the depth and diameter of ablation. However the di
... Show MoreThe objective of this paper was to study the laser spot welding process of low carbon steel sheet. The investigations were based on analytical and finite element analyses. The analytical analysis was focused on a consistent set of equations representing interaction of the laser beam with materials. The numerical analysis based on 3-D finite element analysis of heat flow during laser spot welding taken into account the temperature dependence of the physical properties and latent heat of transformations using ANSYS code V.10.0 to simulate the laser welding process. The effect of laser operating parameters on the results of the temperature profile were studied in addition to the effect on thermal stresses and dimensions of the laser w
... Show MoreCloth simulation and animation has been the topic of research since the mid-80's in the field of computer graphics. Enforcing incompressible is very important in real time simulation. Although, there are great achievements in this regard, it still suffers from unnecessary time consumption in certain steps that is common in real time applications. This research develops a real-time cloth simulator for a virtual human character (VHC) with wearable clothing. This research achieves success in cloth simulation on the VHC through enhancing the position-based dynamics (PBD) framework by computing a series of positional constraints which implement constant densities. Also, the self-collision and collision wit
... Show More
(22)
(20)
Summary:
Background: the immune system differentiates between the endogenous and exogenous bodies that inter the body. The break-down of blood-testis barrier results in the production of antisperm antibodies. This may occur in the case of an infection to the prostate, seminal vesicle and epididymes. Antisperm antibodies (ASA) cause sperm agglutination and affect sperm motility, viability and sperm migration in the female reproductive tract. ASA also impair fertilization process. The objective of the present work was to study the effect of prednisolone on sperm motility index (SMI), viability and sperm penetration assay (SPA) in immunologically infertile men.
Materials and methods: The semen and serum samples of 140 infertile men we
Aims: This study was done to investigate the effect of low energy laser therapy on bone healing at the extraction site. Materials and methods:(24) male albino rats were exposed to the extraction procedure of the maxillary first molar on the first day of a seven day experiment and these animals were divided into two main groups; the control group and the laser group. The laser experiment involved using (Ga-As infrared diode laser) from optodent by directing the probe over the extraction site. The control group consisted of 4 rats, and the laser group was subdivided into 5 subgroups of 4 rats each. The laser dose was as follows: B1: a single dose of 5 minutes immediately after extraction.,
... Show MoreIn the present work usedNd:YAG laser systems of different output characteristic were employed to study the drilling process of material used in scientific and industrial fields. This material include Manganese hard steel. Our study went into the affecting parameters in drilling of Manganese hard steel by laser. Drilling process is achieved through material absorption of part of the incident laser beam. It is the resultant of interfering both, laser beam and material properties and the focusing conditions of the beam. The results as shown that the increase in the laser pulse energy over the used level has raised the hole diameter, depth and increased the hole taper. In addition to that a hole taper was affected by the laser energy, the fo
... Show MoreAbstract
The role of the independent variable and human resources capabilities was the role of the adopted variable. The aim of the research is to identify the level of participation in the knowledge of the organization through human resources and the rigorous scientific investigation to develop new mechanisms of action that help To manage the organization in the implementation of its mission and achieve its main objectives that have been found for it is to encourage the work of scientific research and maintain the preservation of its continuity to increase the competencies of knowledge, technical and skill to form a future workforce qualified to work In the sectors of society.
(1)
We notice that the issue of development is one of the most important issues in ourepoch especially in our country which classify within back ward countries.
When we talk here about the development we don’t mean only the development of capitals or the development of products.but the most important thing is the development of mind .if we notice the experience of developits economy and it didn’t reach to the wanted aim.because these sides . The highness of the meutal rate of the nation is the standard of of the nation is the standard of the sentific and cultural advance for this nation .And that is what we have noticed in human societies ingenerall .
We noticed that
... Show MoreThis paper presents a control system to make the robotic hand mimic human hand motion in real time and offline mode. The human hand tracking system is a wearable sensing arm (potentiometers) used to determine the position in space and to sense the grasping task of human hand. The maskable sensing arm was designed with same geometrical arrangement of robotic hand that needs to be controlled. The control software of a robot was implemented using Visual Basic and supported with graphical user interface (GUI). The control algorithm depends on joint to joint mapping method to match between the motions at each joint of portable sensing arm with corresponding joint of a robot in order to make the robot mimic the motion.