In this research, a variable stiffness actuator is proposed to enhance the damping of the mechanical vibrating system. The frequency response analysis of the vibrating system is dependant in order to analyze and synthesis this semi-active damping, where the suggested process is using active filter to estimate the present frequency of the vibration system, and this will limit the value of the stiffness of the vibrated system. Two active filter s are needed, low-pass-filter (LPF) to choose the higher stiffness of the actuator at small frequencies as well as more damping and high-pass-filter (HPF) to choose the lower stiffness of the actuator at high frequencies as well as more damping, and so

In this study, the mechanical properties of an epoxy and unidirectional woven carbon with fiberglass composite were experimentally investigated. When preparing the composite samples, American Society for Testing and Materials (ASTM)standard was used. Tensile, impact and flexural test were conducted to investigate the mechanical properties of the new produced epoxy Unidirectional Woven Carbon and Epoxy Fiberglass composites. The outcome showed that the strength of the produced samples increased with the increase in the number of unidirectional woven carbon layers added. Two methods were utilized: (1) woven carbon composite with glass fiber (2) woven carbon composite). The two methods of composite were compared with each other.  The resul

BackgroundThe diagnosis and important aspects in treating acute abdomen during pregnancy tend to be delayed due to the peculiar physiological features of pregnancy and the restrictions imposed on imaging diagnostic techniques such as x-ray and CT.Aim of the studyTo identify the most common causes of acute abdomen during pregnancy and identifying the approaches for early diagnosis and to take a correct decision for surgery and assigning the complications that may occur during and/or after surgery for the mother and the fetus.Patients and Methods This is a prospective study that involves data obtained from 91 pregnant patients admitted in the surgical wards in Baghdad teaching hospital during the period from January 2008 to December 2009 .

The design of components subjected to contact stress as local compressive stress is important in engineering application especially in ball and socket Joining.  Two kinds of contact stress are introduced in the ball and socket joint, the first is from normal contact while the other is from sliding contact. Although joining two long links (drive shaft in steering cars) will cause the effect of flexural and tensional buckling stress in hollow columns through the ball and socket ends on the failure condition of the joining mechanism. In this paper the consideration of the combined effect of buckling Load and contact stress on the ball and socket joints have been taken, epically on the stress distribution in the contact area. Different

This research is aiming to find the effective role of the personality characteristics of the Leader in business organization entrepreneurship by studying the effect of the special dimensions of personality characteristics (neuroticism, extraversion, openness, Agreeableness, and conscientiousness) on business organizations entrepreneurship dimensions representing in the two main dimensions (entrepreneurship direction and strategic entrepreneurship) across field study was conducted in thirteen private colleges in Baghdad.

The problem of the research relies in asking the question, is there an effect for Leader personality characteristics on business organizations entrepreneurship. and statistical methods hav

This research includes interested in studying art contemporary, by studying the experiences of sculpture for the formation of post-modernism, assuming the existence of trends in public art can be classified, in spite of the multiplicity of styles and methods of work since the second half of the twentieth century to the present day, and this shenanigans knowledge on how to the Technical that is the art is not restricted, It is art refuses laws and fixed values and traditional styles, and always aspires to diversity and innovation.Search contains three chapters and an introduction containing information about the research problem and the importance of research and the goal of the research, the goal of research is: Detection of artistic tre

Shiranish formation has been divided into two microfacies units: 1-Marly biowacke stone facies 2-Biogenic pack stone facies These microfacies reflected marine deep shelf margin in the upper part of the formation, the lower part was deeper. 238 slides were investigated depending on Mineralogical, compositional and Biological processes, which reflect deep shelf margin at upper part of the formation, but at the lower part open sea environment. The age of the formation is estimated depending on the recognized biostratigraphic zone using the index fossils to be Upper- Middle Maestrichtian.

Abstract

     Machining residual stresses correlate very closely with the cutting parameters and the tool geometries. This research work aims to investigate the effect of cutting speed, feed rate and depth of cut on the surface residual stress of steel AISI 1045 after face milling operation. After each milling test, the residual stress on the surface of the workpiece was measured by using X-ray diffraction technique. Design of Experiment (DOE) software was employed using the response surface methodology (RSM) technique with a central composite rotatable design to build a mathematical model to determine the relationship between the input variables and the response. The results showed that both

In this publication, several six coordinate bridged-polymeric metal complexes are reported. The reaction of 4,4`-dipyridine with ethyl chloroacetate in mole ratio of 1:2 gave the multidentate carboxylate ligand bis(N-carboxylatomethyl)-4,4`-dipyridinium). The reaction of the ligand with metal chloride and sodium azide resulted in the formation of the required polymeric complexes. Upon complex formation, the carboxylato ligand behaves as a neutral multidantate species. The mode of bonding and overall geometry of the complexes were determined through physicochemical and spectroscopic methods. These studies revealed octahedral geometry about metal centres and complexes of the general formula [Cr2(L)(N3)4]Cl2.H2O, Na2[Ag2(L)(N3)4].H2O and [M2(L

The free zone or the free economy cities are cities with classification and functional specificity, although the history of  the concept of these areas has been It dates back to distant eras, but the intellectual and philosophical construction with the support of intellectual approaches, the most important of which is globalization contributed to its rapid spread globally and taking a variety of forms and models. With the diversity of its formulas and objectives countries have competed in adopting the establishment of these areas, meanwhile The influence of related trends affected the contemporary formation of these sites. Therefore ,the research was directed focus on the importance of adopting a set of common indicators (collection