Diesel engine oil was subjected to thermal oxidization (TO) for six periods of time (0 h, 24 h, 48 h, 72 h, 96 h, and 120 h) and was subsequently characterized by terahertz time domain spectroscopy (THz-TDS). The THz refractive index generally increased with oxidation time. The measurement method illustrated the potential of THz-TDS when a fixed setup with a single cuvette is used. A future miniaturized setup installed in an engine would be an example of a fixed setup. For the refractive index, there were highly significant differences among the oxidation times across most of the 0.3–1.7 THz range.

In this research, the effect of reinforcing epoxy resin composites with a filler derived from chopped agriculture waste from oil palm (OP). Epoxy/OP composites were formed by dispersing (1, 3, 5, and 10 wt%) OP filler using a high-speed mechanical stirrer utilizing a hand lay-up method. The effect of adding zinc oxide (ZnO) nanoparticles, with an average size of 10-30 nm, with different wt% (1,2,3, and 5wt%) to the epoxy/oil palm composite,  on the behavior of an epoxy/oil palm composite was studied with different ratios (1,2,3, and 5wt%) and an average size of  10-30 nm.  Fourier Transform Infrared (FTIR) spectrometry and mechanical properties (tensile, impact, hardness, and wear rate) were used to examine the composites. The FTIR

     The Nahr Umr Formation is considered one of the main reservoirs produced in southern Iraq. It is one of the important siliciclastic deposits of the Cretaceous sequence of Iraq oilfields. Zubair oil fields ZB-190 and ZB-047 were chosen to study areas. This study depends on the available core and cutting samples to determine the facies analysis, depositional environments, petrographic characteristics and diagenesis processes. Based on the description of the core and the borehole, six types of facies were distinguished in the Nahr Umr Formation, resulting in an intercalated sandstone and shale with a thin layer of siltstone. The petrographic study of the clastic part of the Nahr Umr Formation showed that the sandstone is composed m

The study deals with 3D seismic reflection in the central Iraq within Merjan oil field which is located approximately (130 km) to the southwest Baghdad and south of Razaza. The 3D seismic survey was interpreted; the results showed that the oil is found within Hartha Formation as stratigraphic traps and with the absence of structural traps. The major normal faults picked are trending N-S direction. There are also minor faults observed using the instantaneous phase and frequency sections, they proved the presence of the faults and showed that the ending of the Safawi reflector toward the north and northeast to the south and southeast and near the western border of fault because of the facies change in the area. The reflector shows a struct

      The Mishrif Formation (Cenomanian – Early Turonian) is an important geologic formation in southern Iraq due to its petrophysical properties and geographic extensions, making it a good reservoir of hydrocarbons. Petrophysical properties of the Mishrif Formation in the current study at the Nasiriya oil field were determined from the interpretation of three open-hole logs data of (NS-1, NS-2, and NS-3) wells.

The results of the Mishrif petrophysical evaluation showed that the formation consists of five variable units (CRI, MA, CRII, MB1 and MB2), each one characterized by distinct petrophysical characteristics.

The upper (MA) and lower (MB) units were determined using electrical, porosity and gamma-ray logs. A sha

On-site pit is the most common option that may be used to dispose drilling wastes. The contents of these pits vary, depending on the lithology of formations drilled and the drilling mud ,and different chemical additives.
Eighty samples of mud (sludge) and eighty samples of water have been collected from ten pits of two Iraqi oilfields(North Rumaila and South Rumaila/southern Iraq) and were chemically analyzed for metals Cr, Pb,As, Zn, Fe, Mn,K , Na,Ba, Ca, Mg,SO4=,and Cl- in order to determine the quality and quantity content of studied reserve pits
Inefficient equipment, using toxic materials for various drilling processes, absence of regulations for the design and monitoring of pit during and after drilling operation, and leaking

The Gas Assisted Gravity Drainage (GAGD) process has become one of the most important processes to enhance oil recovery in both secondary and tertiary recovery stages and through immiscible and miscible modes.  Its advantages came from the ability to provide gravity-stable oil displacement for improving oil recovery, when compared with conventional gas injection methods such as Continuous Gas Injection (CGI) and Water – Alternative Gas (WAG).

Vertical injectors for CO₂   gas were placed at the top of the reservoir to form a gas cap which drives the oil towards the horizontal oil producing wells which are located above the oil-water-contact. The GAGD process was developed and tested in vertical wel

This study focuses on the use of an optimum amount of Sodium Polyacrylate (SP) for designing cement slurry with the high performance of rheological properties and displacement efficiency. A laboratory study has been carried out on the cement slurry which prepared with SP as superabsorbent polymer. SP has been providing an internal water source that helps in the hydration process, and curing and ultimately increases the cement strength. Also improves the cement performance by improving the cement stability. Several batches were prepared to determine the proper amount of SP to add it in the cement slurry. Also, we studied its effect on cement density, amount of free water in order to observe the rheological properties, and thickening time.

In the present work, asphaltenes and resins separated from emulsion samples collected from two Iraqi oil wells, Nafut Kana (Nk) and Basrah were used to study the emulsion stability. The effect of oil resins to asphaltene (R/A) ratio, pH of the aqueous phase, addition of paraffinic solvent (n-heptane), aromatic solvent (toluene), and blend of both (heptol) in various proportions on the stability of emulsions had been investigated. The conditions of experiments were specified as an agitation speed of 1000 rpm for 30 minutes, heating at 50 °C, and water content of 30%.  The results showed that as the R/A ratio increases, the emulsion will be unstable and the amount of water separated from emulsion increases. It was noticed that the em

Crude oil is one of the most important sources of energy in the world. To extract its multiple components, we need oil refineries. Refineries consist of multiple parts, including heat exchangers, furnaces, and others. It is known that one of the initial operations in the refineries is the process of gradually raising the temperature of crude oil to 370 degrees centigrade or higher. Hence, in this investigation the focus is on the furnaces and the corrosion in their tubes. The investigation was accomplished by reading the thickness of the tubes for the period from 2008 to 2020 with a test in every two year, had passed from their introduction into the work. Where the thickness of more than one point was measured on each tube in the sa