Two grades of paving asphalt with penetration of 46 and 65 are studied for determining changes in their physical and chemical properties caused by ageing.
The ageing process has been conducted on two petroleum paving asphalt cement using thin film oven test at 150, 163 and 175 C, and ageing time 5, 10,15, 20, 25 and 30 hours. The effect of ageing time and temperature on penetration, kinematic viscosity, softening point, solubility in trichloroethylene, heat loss and changes in chemical composition are investigated. The results of thin film oven test process indicte that the asphaltenes concentration of all aged asphalt increases with increasing ageing time, while the opposite was observed for polar-aromatic and naphthene-aromatic. The saturate of low penetration grade asphalt is higher than that for high penetration grade asphalt and remained unchanged with ageing time. Th kinematic viscosity and softening point seem to increase with increasing ageing time, while the penetration decreases with increasing ageing time. The DI of aged asphalt inreases with increasing ageing time.
Bacopa monnieri L. (Scrophulariaceae), synoname is Herpestis monniera that provides bioactive compounds, especially triterpenoid saponins (Bacosides) which exhibits an important biological activities, like hypothyroidism, anticonvulsant, memory enhancing and antistress. Because there are no researches about B. monnieri L. plant that grow in Iraq, and there active compounds especially triterpenoid saponin (TS), and there effects. This study was detected the presence of (TS) in, and examined the cytotoxic and the antioxidant activity of these compounds in vitro. The study was included the extraction and identification of TS from the whole parts of B. monnieri L. by using three methods, and the best yield was analyzed by High Performance Liqui
... Show MoreThe influence of pre- shot peening and welding parameters on mechanical and metallurgical properties of dissimilar and similar aluminum alloys AA2024-T3 and AA6061-T6 joints using friction stir welding have been studied. In this work, numbers of plates were equipped from sheet alloys in dimensions (150*50*6) mm then some of them were exposed to shot peening process before friction stir welding using steel ball having diameter 1.25 mm for period of 15 minutes. FSW joints were manufactured from plates at three welding speeds (28, 40, 56 mm/min) and welding speed 40mm/min was chosen at a rotating speed of 1400 rpm for welding the dissimilar pre- shot plates. Tow joints were made at rotational speed of 1000 rpm and welding speed of 40m/min f
... Show MoreSilver sulfide and the thin films Ag2Se0.8Te0.2 and Ag2Se0.8S0.2 created by the thermal evaporation process on glass with a thickness of 350 nm were examined for their structural and optical properties. These films were made at a temperature of 300 K. According to the X-ray diffraction investigation, the films are polycrystalline and have an initial orthorhombic phase. Using X-ray diffraction research, the crystallization orientations of Ag2Se and Ag2Se0.8Te0.2 & Ag2Se0.8S0.2 (23.304, 49.91) were discovered (XRD). As (Ag2Se and Ag2Se0.8Te0.2 & Ag2Se0.8S0.2) absorption coefficient fell from (470-774) nm, the optical band gap increased (2.15 & 2 & 2.25eV). For instance, the characteristics of thin films made of Ag2Se0.8Te0.2 and Ag2Se0.8S0.2
... Show MoreThe research aimed to prepare a psychological counseling program for the coaches of the Sports Care Center in the gymnasium, and to learn about the impact of the psychological counseling program in reducing irrational ideas and causal attribution of the coaches of the Sports Talent Care Center in the gymnasium, to assume that there are statistically significant differences between the results of the tribal and posttests of the research group Experimental in the scale of irrational ideas, and there are statistically significant differences between the results of the tribal and posttests of the experimental research group in the scale of the causal attribution scale, The experimental approach was adopted by designing one experimental
... Show MorePraise be to God, Lord of the worlds, and prayers and peace be upon our master Muhammad and upon his family and companions.
And after:
Muslim scholars have fought in the extent of regard to these interests, each according to his opinion and according to his evaluation, and his consideration of this interest, but it remains important that the legislation in them needs more precaution and caution against the predominance of passions, because the passions often decorate spoilers so they see an interest, so practical application must To realize the spirit of Islamic Sharia in its entirety of its rulings, and the preponderance between the interests and evils that prevail in our societies, which c
... Show MoreJudaism followed the approach of monotheism after God Almighty sent Moses (peace be upon him) to convey to them the messages of their Lord, so that they might be on a right guidance and path, but the people did not follow that path.” Love of matter and faith in what is witnessed, so they portrayed the Lord in several images in line with what their souls drew upon them.
The achievement of world peace is a humanitarian demand that humanity has sought since its existence. Despite the international and regional efforts to achieve this demand, it is still reaching its desired ambitions if conflicts, contradictions, and internal and external wars continue to justify us clearly in terms of ethnic, religious and sectarian conflict. The revolution of informatics and the impact of globalization opened a new era of communication and openness and the negative and positive impact of others, which re-published and distributed values, ideas and new cultures Some of them carries extremist ideas urging violence and destruction and other abolition, it became necessary to follow policies and reward The culture of peace,
... Show MoreAbstract
Experimental work from Magnetic Abrasive Finishing (MAF) tests was carried out design parameters (amplitude, and number of cycle which are formed the shape of electromagnetic pole), and technological parameters (current, cutting speed, working gap, and finishing time) all have an influence on the mechanical properties of the surface layer in MAF process. This research has made to study the effect of design and technological parameters on the surface roughness (Ra), micro hardness (Hv) and material removal (MR) in working zone. A set of experimental tests has been planned using response surface methodology according to Taguchi matrix (36) with three levels and six factors
... Show More