In this research, the results of the Integral breadth method were used to analyze the X-ray lines to determine the crystallite size and lattice strain of the zirconium oxide nanoparticles and the value of the crystal size was equal to (8.2nm) and the lattice strain (0.001955), and then the results were compared with three other methods, which are the Scherer and Scherer dynamical diffraction theory and two formulas of the Scherer and Wilson method.the results were as followsScherer crystallite size(7.4nm)and lattice strain(0.011968),Schererdynamic method crystallite size(7.5 nm),Scherrer and Wilson methodcrystallite size( 8.5nm) and lattice strain( 0.001919).And using another formula for Schearer and Wilson methodwe obtain the size of the crystal(8.9nm). The difference in the results calculated for each of these methods was observed in this study.
Objective: To suggest a weighted measure to diagnose the reasons for the low student success ratios in mathematics concerning the third grade of intermediate schools in light of components educational system represented by: [Students, Teachers, Curriculum, and Environmental reasons (others reasons)] assuming differentiated and interrelated components, Also the effectiveness forming of these components according to the gender variable. Methods: Data collection tools were prepared by constructing two questionnaires for each of (Students and Teachers), which included a number of items that involved some domains for studied components of educational system, which demonstrated a high level of validity and reliability in the pilot study, in addi
... Show MoreThe added value of internal audit greatly contributes to adding value to the institution, but most departments of economic units in Iraq neglected the role of internal audit and the added value that can be achieved by those institutions, since the term added value of internal audit is a relatively vague term from the premise that what cannot be measured is difficult Determine it, and perhaps descriptive standards for it is the extent of compliance with international auditing standards (IIA).
The research aims to study the procedures and results of auditing to verify that they have given an added value to the audit with a positive impact, develop its aspects and research, identify deficiencies for the audi
... Show MoreThis study focuses on the biodegradation of oxymatrine insecticide by some soil fungi isolated from four agriculture stations. The results showed that the highest degradation rate 94.66% was recorded by Ulocladium sp. at 10 days and A. niger recorded the lowest degradation rate 45.86%, while at 20 days Ulocladium sp. also showed the highest degradation rate 94.98% and the lowest degradation rate reached to 82.49% with A.niger. The mix (Exerohilum sp.+Ulocladium sp.) recorded the highest degradation rate of oxymatrine insecticide 90.22%, 88.51%, 85.34% at 4, 8 and 12 ppm.The use of mixed isolates enhanced the biodegradation process. There is no study of oxymatrine biodegradation
... Show MoreThis research discusses one of the largest and most important issues of a doctrinal and philosophical dimension at the same time, which is the issue of man’s freedom to choose his actions, and thus his responsibility for those actions, by looking at the nature of these acts, their being and the origin of their creation. He showed that they were created in man by force, and that he was their original creator, and that they were among the creatures of the God Almighty God like others, but they are attributed to man through acquisition. So to the first saying went Jahmiyya or Jabariyya, and to the second saying went to fatalism in the past, and the existentialists shared with them in the modern era, and to the third saying went to the Sun
... Show MoreThis paper presents numerical and experimental stress analyses to evaluate the contact and bending stresses on the teeth of spiral bevel gear drive. Finite Element Method has been adopted as a numerical technique which accomplished basically by using ANSYS software package. The experimental stress analysis has been achieved by using a gear tooth model made of Castolite material which has photoelastic properties. The main goal of this research is detecting the maximum tooth stresses to avoid the severe areas that caused tooth failure and to increase the working life for this type of gear drives.
Computer analysis of simple eye model is performed in the present work by using the Zemax optical design software 2000E . The most important optical parameters of the eye were calculated such as the effective focal length (EFL) , the image spot size at the retina and found to be in a reasonable agreement with the values needed for the laser retinal treatment .The present eye model leads to an effective wavelength and we found the image spot diagram at the surface of the retina and the wavefront error which are provided at zero field angle. This gives a good evidence of the validity of the model in one hand, and can be used to determine the compatibility of any optical design intended for visual applications. By using the pulse fre
... Show MoreAn indoor spraying robot is built in this research to solve numerous challenges associated with manual spraying. The mechanical, hardware and essential technologies used are all detailed and designed. The proposed spraying robot's conceptual design is split into two parts: hardware and software. The mechanical design, manufacturing, electrical, and electronics systems are described in the hardware part, while the control of the robot is described in the software section. This robot's kinematic and dynamic models were developed using three links that move in the x, y, and z directions. The robot was then designed using SolidWorks software to compute each connection's deflection and maximum stresses. The characteristics of the stepper moto
... Show MoreThere were signs of the first civilization known to humanity for more than 6000 years BC in the north of Iraq have disappeared this civilization to appear after 500 years in southern Iraq, the Sumerian civilization, which was considered as the opinion of scientists or civilizations, exceeds the impact to Asia and the countries that had been in contact (Sumerians) and see them today in other towns and villages. In subsequent periods of time appeared distinct personalities to their nature, religious, social, special clothing with clothes seem especially long. And usually dress is made from raw wool material making them in the Sumerian era. Put the garment on the body and leaves the top of the right shoulder with the survival of an ope
... Show MoreThis work presents mainly the buckling load of sandwich plates with or without crack for different cases. The buckling loads are analyzed experimentally and numerically by using ANSYS 15. The experimental investigation was to fabricate the cracked sandwich plate from stainless steel and PVC to find mechanical properties of stainless steel and PVC such as young modulus. The buckling load for different aspect ratio, crack length, cracked location and plate without crack found. The experimental results were compared with that found from ANSYS program. Present of crack is decreased the buckling load and that depends on crack size, crack location and aspect ratio.