Nanofluids (dispersion of nanoparticles in a base fluid) have been suggested as promising agents in subsurface industries including enhanced oil recovery. Nanoparticles can easily pass through small pore throats in reservoirs formations; however, physicochemical interactions between nanoparticles and between nanoparticles and rocks can cause a significant retention of nanoparticles. This study investigated the transport, attach, and retention of silica nanoparticles in core plugs. The hydrophilic silica nanoparticles were injected into limestone core as nanofluid of different nanoparticles size (5 nm, and 20 nm), concentration (0.005 – 0.1 wt% SiO2), and base fluid salinity (0 – 3 wt% NaCl) at different temperatures (23, and 50 °C). Deposition and transport of nanoparticles were measured via nanoparticle concentration of effluent fluid, and energy distractive spectroscopy (EDS) measurement on the limestone core. It was found that silica nanoparticles dispersed in brine (NaCl) solutions are increasingly retained in limestone core as the solution ionic strength increases. On the other hand, less significant retention was measured when the nanoparticles were dispersed in DI water. The EDS measurements also reported the same trend of increased nanoparticles retention with salinity due to larger aggregates that result from the screening effect of the electrolyte on repulsive forces between nanoparticles. Thus, the observed change in surface wettability from oil to water-wet and the increase in oil production that reported in many core flooding laboratory studies are mainly related to the high adsorption rate of hydrophilic silica nanoparticles on carbonate surfaces.
To observe the effect of media of the internal pressure on the equivalent stress distribution in the tube, an experimental study is done by constructing a testing rig to apply the hydraulic pressure and three dies are manufactured with different bulging configurations (square, cosine, and conical). In the other part, ANSYS APDL is generated to analyze the bulging process with hydraulic and rubber (natural and industrial) media. It was found that when the media is a rubber, the stress is decreased about 9.068% in case of cosine die and 5.4439% in case of conical die and 2.8544% in case of square die. So, it can be concluded that the internal pressure in the rubber media is much better than in hydraulic media. Also, the force needed for fo
... Show MoreUnderstanding, promoting, and teaching media literacy is an important societal challenge. STEM educators are increasingly looking to incorporate 21st century skills such as media literacy into core subject education. In this paper we investigate how undergraduate Computer Science (CS) students can learn media literacy as a by-product of collaborative video tutorial production. The paper presents a study of 34 third-year CS undergraduates who, as part of their learning, were each asked to produce three video tutorials on Raspberry Pi programming, using a collaborative video production tool for mobile phones (Bootlegger). We provide results of both quantitative and qualitative analysis of the production process and resulting video tutorials,
... Show MoreBackground: It has been accepted that in patients with CSOM, conductive deafness results from mechanical break-down of sound conduction ,whilist the cochlea remains unaffected.
Objectives: Our study aims to prove a sensorineural component in hearing loss in patients suffering from CSOM , which necissates early detection as it increases in severity with time.
Methods: A prospective study was done on 64 patients, all were diagnosed as having unilateral CSOM, their ages ranged from 18-40 years to exclude presbyacusis as a cause of sensorineural deafness.
These patients were divided into 4 groups according to the duration of discharge and further divided into 3 groups according to the pathology (simple perforation, granulation tissu
In the spreading of the Internet, mobile smart devices, and interactive websites such as YouTube, the educational video becomes more widespread and deliberative among users. The reasons for its spread are the prevalence of technologies, cheap cost, and easy to use. However, these products often lack to the distinction in video production. By following videos of an educational channel on YouTube, some comments found to discuss the lack of the content presented to motivate the learners, which lead to reduce the viewers of the videos. Therefore, there is an important decision to find general standards for the design and production of educational videos. A list of standards has been drawn up to help those interested in producing educational
... Show MoreIn the spreading of the Internet, mobile smart devices, and interactive websites such as YouTube, the educational video becomes more widespread and deliberative among users. The reasons for its spread are the prevalence of technologies, cheap cost, and easy to use. However, these products often lack to the distinction in video production. By following videos of an educational channel on YouTube, some comments found to discuss the lack of the content presented to motivate the learners, which lead to reduce the viewers of the videos. Therefore, there is an important decision to find general standards for the design and production of educational videos. A list of standards has been drawn up to help those interested in producing educational
... Show MoreBackground. Nanocoating of biomedical materials may be considered the most essential developing field recently, primarily directed at improving their tribological behaviors that enhance their performance and durability. In orthodontics, as in many medical fields, friction reduction (by nanocoatings) among different orthodontic components is considered a substantial milestone in the development of biomedical technology that reduces orthodontic treatment time. The objective of the current research was to explore the tribological behavior, namely, friction of nanocoated thin layer by tantalum (Ta), niobium (Nb), and vanadium (V) manufactured using plasma sputtering at 1, 2, and 3 hours on substrates made of 316L stainless steel (SS),
... Show MorePolyacrylamide Solutions of different concentrations (0.2, 0.4, 0.6, 0.8, 1.0 %) of Ag nanoparticles and ZnO nanoparticles were prepared, the viscosities and surface tension were measured for all solutions, where measurements indicated an increase in these properties with increased concentration, where the relative viscosity of polyacrylamide/zinc nanoparticles increased from 1.275 to 2.243, and the relative viscosity of polyacrylamide/silver nanoparticles increased from 1.178 to 1.934. Viscosity is significant parameters during electrospinning process. While the surface tension of the polyacrylamide/zinc nanoparticles has changed from 0.0343 Nm-1 to .0.0.0 Nm-1 and changed from .0.000Nm-1 to.0.0.0 Nm-1. Also the constants KH and KK were
... Show MoreThe objective of the present investigation was to enhance the solubility of practically insoluble mirtazapine by preparing nanosuspension, prepared by using solvent anti solvent technology. Mirtazapine is practically insoluble in water which act as antidepressant .It was prepared as nano particles in order to improve its solubility and dissolution rate. Twenty formulas were prepared and different stabilizing agents were used with different concentrations such as poly vinyl pyrrolidone (PVPK-90), poly vinyl alcohol (PVA), poloxamer 188 and poloxamer 407. The ratios of drug to stabilizers used to prepare the nanoparticles were 1: 1 and 1:2. The prepared nanoparticles were evaluated for
... Show More