Experiment was conducted in Baghdad, three factor were used in this research included Two types of Plows included moldboard and disk plows which represented the main plot, Three forward speeds of the tillage was the second factor included 1.85, 3.75 and 5.62 km / h which represented sup plot , and Three levels of Soil Moisture was third factor included 21, 18 and 14 % in all of Vertical and Lateral Plowing Deviation, Practical and specific productivity, actual time for plowing one donam and appearance (goodness) of Tillage represented by the number of clods > 10 cm in silt clay loam soil with depth 22 cm were studied. the experiment was used Split – split plot design under randomized complete block design with three replications and Least Significant Design 5 % was used to compare the means of treatments . Mold-board plow recorded the best Practical and specific productivity for plowing which was 1.247 donam/ hr and 2379 m / hr, and lower actual time for plowing one donam 0.972 hr and Appearance Tillage number of clods > 10 cm was 9.555 clods/m2 , Disc Plow recorded the least Vertical and Lateral Deviation for Plowing which was 2.325% and 2.357% . Tillage Speed 5.62 km/hr recorded higher Practical and specific productivity 1.672 donam/hr and 3452 m/hr respectively and lower actual time 0.608 hr and number of clods > 10 cm was 8.166 clods/m2, Speed 1.85 km/hr recorded lower Vertical and Lateral Deviation Plowing 1.221% and 1.068% respectively. Soil Moisture 18 % recorded higher Practical and specific productivity 1.168 donam /hr and 2400 m /hr respectively, lower actual time 1.047 hr and lower number of clods > 10 cm was 9.500 clods/m2. Soil Moisture 21% recorded lower Vertical and Lateral Deviation for Plowing 1.978% and 1.901% respectively. All Interactions among treatments had significant effect on the parameters studded under this experiment.
Ball and Plate (B&P) system is a benchmark system in the control engineering field that has been used to verify many control methods. In this paper the design of a sliding mode . controller has been investigated and verified in real-time via implementation on a real ball and plate system hardware. The mathematical model has been derived and the necessary parameters have been measured. The sliding mode controller has been designed based on the obtained mathematical model. The resulting controller has been implemented using the Arduino Mega 2560 and a ball and plate system built completely from scratch. The Arduino has been programmed by the Arduino support target for Simulink. Three test signals has been used for verification purposes
... Show MoreThe alluvial fan of Mandali located between latitude 30˚45’00” N longitude 45˚30’00” E in east of Diyala Governorate, Iraq. Thirty-five wells were identified in the study area with average depth of 84 m and estimated area of 21550 ha. A three-dimensional conceptual model was prepared by using GMS program. From wells cross sections, four geological layers have been identified. The hydraulic conductivity of these layers was calculated for steady state condition, where the water levels for nine wells distributed over the study area were observed at same time. Afterward, PEST facility in the GMS was used to estimate the aquifer hydraulic characteristics. Other characteristics such as storage coefficient and specific yield have
... Show MoreAbstract: Choosing suitable artificial teeth for partially edentulous patients and arranging these teeth in a way to look natural is difficult. An important factor in dentures construction is the mesiodistal width of anterior teeth, because a denture would not appearance natural if artificial teeth are of incorrect size. While for a successful orthodontic treatment, mesiodeistal width of teeth is important for space analysis and for establishing proper occlusion. The aim of this study is to determine the correlation between the average mesiodistal width of anterior and posterior teeth in male and female Iraqi population. 40 Iraqi subjects with normal occlusion participated in this study. Mesiodistal measurement of all teeth was carried out
... Show MoreFusidic acid (FA) is a well-known pharmaceutical antibiotic used to treat dermal infections. This experiment aimed for developing a standardized HPLC protocol to determine the accurate concentration of fusidic acid in both non-ionic and cationic nano-emulsion based gels. For this purpose, a simple, precise, accurate approach was developed. A column with reversed-phase C18 (250 mm x 4.6 mm ID x 5 m) was utilized for the separation process. The main constituents of the HPLC mobile phase were composed of water: acetonitrile (1: 4); adjusted at pH 3.3. The flow rate was 1.0 mL/minute. The optimized wavelength was selected at 235 nm. This approach achieved strong linearity for alcoholic solutions of FA when loaded at a serial concentrati
... Show MoreThe aim of the research is to prepare motor sense exercises for developing motor and physiological abilities of backstroke and forward stroke service skill in badminton and investigated their effect. The research is adopted the experimental method with two groups design. The sample of the research is 8 players (13-15 years). The sample is divided into two groups of 4 players for each group. Both groups are exposed to pre and post tests, after the experimented were finished, the results are statically analyzed. The results have showed that there are positive developing abilities of motor and physiological of service skill in badminton. Finally, these prepared exercises are recommended for developing players’ abilities in badminton.
Need organizations today to move towards strategic thinking which means analyzing situations faced by particular challenges of change in the external environment, which makes it imperative for The Organization That to reconsider their strategies and orientations and operations, a so-called re-engineering to meet those challenges and pressures, to try to achieve improvement root in the installation of the organization and methodscompletion of its work towards achieving high levels of performance and that is reflected to achieve its objectives, and this is what aims to Current search to deal with implications characteristics of strategic thinking in the stages of application re-engineering business of the company General Industries
... Show MoreBackground: Toxoplasmosis is a very common infection caused by the obligate intracellular protozoan parasite. This parasite is called Toxoplasma gondii widely distributed around the world . Toxoplasma gondii can be vertically transmitted to the fetus during pregnancy and may cause wide range of clinical manifestations in the offspring.
Objective: To determine seroprevalence Immunoglobulin G (IgG) and Immunoglobulin M (IgM ) to toxoplasma gondii among pregnant women and to identify the risk factors.
Type of the study: A cross-sectional study.
Methods: A total of 110 blood samples of pregnant women were collected from
... Show More