Cysteine-cysteine chemokine ligand 5 (CCL5) is known to play an important role with immunoregulatory and inflammatory activities in the formation of granuloma during infection with Mycobacterium tuberculosis. About 90 subjects, involving 50 patients with pulmonary TB and 40 apparently healthy individuals (as a control group) were collected from primary health care center\AL-Sadur city sector/ Baghdad City/ Iraq, and at specialized chest and respiratory diseases center in Wassit City /Iraq during the period from January 2019 to May 2019. The study was carried out to investigate serum level of CCL-5 of both patients and control by using enzyme linked immunosorbent assay (ELISA), and to determine the association between CCL5 genotypes with pulmonary tuberculosis susceptibility in Iraqi population. Genotyping analysis of CCL5 rs2107538 was performed by using amplification refractory mutation system (ARMS-PCR) method. The results revealed that serum levels of CCL-5 was significantly, (P ≤0.01) increased in pulmonary tuberculosis patients compared to control. The mean ±SE of CCL-5 level in PTB patients and controls were 455.40 ±25.35 ng/L and 80.86 ± 5.96 ng/L, respectively. Analysis of H-W equilibrium revealed that CCL-5 rs2107538 GG, GA and AA genotypes in TB patient group were not in agreement with the equilibrium and there was a significant variation (p ≤ 0.05) between the observed and expected frequencies. While control group showed an agreement with the equilibrium. At position rs2107538, CCL-5 GG genotype showed a significant increased level of CCL-5 (531.01 ± 23.03 ng/L) in PTB patients compared to GA genotype (305.28 ± 33.45 ng/L) and AA genotype (150.27 ± 11.60 ng/L) of the patients. This study suggest that CCL-5 could be considered as a good biomarker for diagnosis of PTB, while it exclude the CCL-5 rs2107538 as major risk factor for tuberculosis in the Iraqi population
(4)
(2)
Half of the oil production of the worldwide is a result of the water flooding project. But the main concern of this process is mobility control of the injected fluid, because the unfavorable mobility ratio leads to fingering effect. Adding polymer to the injection water increase the water viscosity, therefore, the displacement will be more stable and have a greater sweep efficiency.
Using of polymer flooding has received more attention these days. Polymer has great potential in the Middle East region, especially in reservoir with high temperature and salinity.
The main objective of this work is to show the effect of shear rate, salinity, temperature, polymer concentration on polymer v
... Show MoreSome maps of the chaotic firefly algorithm were selected to select variables for data on blood diseases and blood vessels obtained from Nasiriyah General Hospital where the data were tested and tracking the distribution of Gamma and it was concluded that a Chebyshevmap method is more efficient than a Sinusoidal map method through mean square error criterion.
The aim of this work is to study the factors that affect the welding joint of dissimilar metals. Austenitic stainless steel-type AISI (316L) with a thickness of (2mm) was welded to carbon steel (1mm) using an MIG spot welding. The filler metal is a welding wire of the type E80S-G (according to AWS) is used with (1.2mm) diameter and CO2 is used as shielding gas with flow rate (7L/min) for all times was used in this work.
The results indicate that the increase of the welding current tends to increase the size of spot weld, and also increases the sheer force. Whereas the sheer force increased inversely with the time of welding. Furthermore, the results indicate that i
... Show MoreSuggested in this study the introduction of monomers have the ability to interact with polyester Rzn way confused or Alchapak Vodev polycarbonate first Almiaal acrylate ????? grains and offered models for high temperature and for a period of time of 40 days and absorbance and penetration and after color changes resulting from the storage heat higher using shades where models were extractedthermal storage and take measurements and then returned periodically results were consistent with theoretical expectations and mixing
In this research, the efficiency of low-cost unmodified wool fibers were used to remove zinc ion from industrial wastewater. Removal of zinc ion was achieved at 99.52% by using simple wool column. The experiment was carried out under varying conditions of (2h) contact time, metal ion concentration (50mg/l), wool fibers quantity to treated water (70g/l), pH(7) & acid concentration (0.05M). The aim of this method is to use a high sensitive, available & cheep natural material which applied successfully for industrial wastewater& synthetic water, where zinc ion concentration was reduced from (14.6mg/l) to (0.07mg/l) & consequently the hazardous effect of contamination was minimized.
(1)
Many experiments were achieved to determine the allelopathic potential of the plant Myrtle parts in which it may affects other plants, like: volatile substances which released from the Myrtle leaves , and its effect examined on the germination (GE) and growth (GR) of the selected crops ; Chickpea ( C ) , Wheat(W) , and Lentil (L)., the aqueous extract of the leaf and the root of the plant examined to test its effect on the (GE) and (GR) of the selected crops ; (C) , (W) , and (L)., also plant residue of (M) and its effect tested on the (GE) and (GR) of the selected crops ; ( C ) , (W) , and (L) . Experiments proceeded on Spring 2007 in the greenhouse conditions , and main results which found were that; the effect of the volatile s
... Show More
(1)
This paper presents a control system to make the robotic hand mimic human hand motion in real time and offline mode. The human hand tracking system is a wearable sensing arm (potentiometers) used to determine the position in space and to sense the grasping task of human hand. The maskable sensing arm was designed with same geometrical arrangement of robotic hand that needs to be controlled. The control software of a robot was implemented using Visual Basic and supported with graphical user interface (GUI). The control algorithm depends on joint to joint mapping method to match between the motions at each joint of portable sensing arm with corresponding joint of a robot in order to make the robot mimic the motion.