Polymer matrix composites are suitable materials for medical applications, such as denture base resin polymethyl methacrylate (PMMA). This includes light weight and high strength. This paper describes the effect of selected weight fractions (1, 2, 3, 4 & 5) % wt of nano(Alumina AL2O3, Zirconia ZrO2, Hydroxyapatite HA and Halloysite nanoClay) reinforcements on the biopolymer matrix (PMMA). Some tribology tests were used to evaluate the prepared system (impact strength, hardness surface, and wear rate) tests. The samples were fabricated by (Hand Lay-Up) with different particle reinforcement percentages. All tests were accomplished at room temperature, and samples were developed according to the ASTM standard. The weight fraction of (4% for AL

Abstract

     In this investigation, Al₂O₃ nano material of 50nm particles size were added to the 6061 Al aluminium alloy by using the stir casting technique to fabricate the nanocomposite of 10wt% Al₂O₃. The experimental results observed that the addition of 10wt% Al₂O₃ improved the fatigue life and strength of constant and cumulative fatigue. Comparison between the S-N curves behaviour of metal matrix (AA6061) and the nanocomposite 10wt% Al₂O₃ has been made. The comparison revealed that 12.8% enhancement in fatigue strength at 10⁷cycles due to 10wt% nano reinforcement. Also cumulative fatigue l

Introduction: The present study was performed to evaluate the influence of a 1064 nm fiber laser on shear bond strength (SBS) at the interface of titanium and resin cement. Methods: Forty titanium discs of 6 mm × 3 mm (diameter and thickness respectively) were categorized into four groups (n=10): control group without any surface treatment and three groups treated with a fiber laser with 81 ns pulse duration, 30 kHz frequency, 10000 mm/s scanning speed, 0.05 mm spot size, and different average power values (3, 5 and 7 W) depending on the tested group. Titanium disc characterization was performed by the scanning electron microscope (SEM) and surface roughness tester. Phase analysis was achieved using an X-ray diffractometer (XRD). F

Objective: The objectives of the present study were to evaluate the effectiveness of the instructional intervention
about medical and health knowledge of patients with diabetes mellitus type II.
Methodology: A Quasi- experimental study was carried out in National Center for Diabetes Mellitus/ Almustansria
University, started from 4th January 2012, to 1st April 2012. Non-probability (purposive sample) of (50) diabetes
mellitus type II, who visit National Center for Diabetes Mellitus/ Almustansria University. The study sample is
divided equally into (25) study and (25) control groups. The study group received the instructional intervention.
While the control not exposed to the instructional intervention. The data are coll

Crocidolomia binotalis (Cb) (Zeller) is one of the main pests of cabbage which is difficult for farmers to control in the Ijen Crater in Indonesia. The demand for cabbage in Indonesia is increasing every year, so intensification efforts are continuously being made. Farmers intensively use synthetic pesticides as the primary control of Cb. The purpose of this study is to examine several control agents that can be used as an alternative to synthetic pesticides. Then, it provides recommendations to Ijen Crater farmers to adapt in reducing the use of synthetic pesticides. The biopesticide used was based on the Nuclear Polyhedrosis Virus strains of Spodoptera litura (SlNPV) and Helicoverpa armigera (HaNPV), botanical pesticides, and

       Optical properties and surface morphology of pure and doped Polystyrene films with different divalent metals of Zn, Cu and Sn and one concentration percentage have been studied. Measurements of UV-Vis spectrophotometer and AFM spectroscopy were determined. The absorbance, transmittance and reflectance spectrums were used to study different optical parameters such as absorption coefficient, refractive index, extinction coefficient and energy gap in the wavelengths rang 200-800nm. These parameters have increased in the presence of the metals. The change in the calculated values of energy gaps with doping metals content has been investigated in terms of PS matrix structural modification. The value of opt

the history of the Scouting movement reflects the global social cultural and technological change over more than a century. scouting aims to develop young people worldwide through educational programs based on specific principles and values. in arab countries, the scouting movement is considered one of the most important platforms contributing to developing young people and enhancing their rule. positive in society, began with the establishment of the first Scout camp in the region and witnessed great growth and prosperity over the decades the research reveals the historical roots and development of the scout movement in the leading arab countries and analyzes the positive impact of scout movement in the leading arab countries on the develo

The interaction in the city is reflected in the movement of people motivated by their activities and their economic and social goals, which include many variables subject to the planning process in the interpretation of this movement and the mapping of trends of transport intensity through the concept of transport function and its functional relationships with the uses of the earth in the sustainability and effectiveness of the movement of transport and Economic activity and population movement. Transport planners are concerned with the requirements of land use, which are linked to and included in the transport planning process as a factor for the future transport needs. There is a strong relationship between the transport system

In this work, the synergistic effect of chlorinated rubber (additive I),with zeolite 3A (additive II), zeolite 4A (additive III), and zeolite 5A (additive IV) in (1:1) weight percentage, on the flammability for unsaturated polyester resin was studied in the weight ratios for (3,7,10,13&15%) by preparing films of (130×130×3) mm in diameters. Three standard test methods used to measure were the flame retardation which are; ASTM: D-2863, ASTM: D- 635& ASTM: D-3014. Results obtained from these tests indicated that all of the additives were effective additive IV has the highest efficiency as a flame retardant.