In this paper, the time-history responses of a square plan two-story reinforced concrete prototype building, considering the elastic and inelastic behavior of the materials, were studied numerically. ABAQUS software was used in three-dimensional (3D) nonlinear dynamic analysis to predict the inelastic response of the buildings. Concrete Damage Plasticity Model (CDPM) has been used to model the inelastic behavior of the reinforced concrete building under seismic excitation. The input data included geometric information, material properties, and the ground motion. The building structure was designed only for gravity load according to ACI 318 with

The aim of this paper is to present a method for solving third order ordinary differential equations with two point boundary condition , we propose two-point osculatory interpolation to construct polynomial solution. The original problem is concerned using two-points osculatory interpolation with the fit equal numbers of derivatives at the end points of an interval [0 , 1] . Also, many examples are presented to demonstrate the applicability, accuracy and efficiency of the method by compared with conventional method .

After the fall of the Third Dynasty of Ur at the hands of the Elamites during the reign of its last ruler, King Ibi-Sin, the Amorites continued to flow more into Mesopotamia in the form of large migrations that established a number of contemporary and conflicting ruling dynasties that formed the Old Babylonian era. Among these dynasties was the Larsa dynasty, founded by King Nablanum in the city of Larsa. The fourth king who ruled in the Larsa dynasty, Gungunum, was one of the most powerful kings who stood up to the Isin dynasty, which had until that time enjoyed great political superiority in the country. The kings who ruled after him expanded their influence and controlled a number of cities, especially the cities of Nippur and Uruk, whic

The construction of embankment for roadway interchange system at urban area is restricted due to the large geometry requirements, since the value of land required for such construction is high, and the area available is limited as compared to rural area. One of the optimum solutions to such problem is the earth reinforcement technique which requires a limited area for embankment construction. Gypseous soil from Al-Anbar governorate area was obtained and subjected to various physical and chemical analysis to determine it is properties. A laboratory model box of 50x50x25 cm was used as a representative embankment; soil has been compacted in five layers at maximum dry density (modified compaction) and an aluminum reinforcement strips were i

PPSU hollow fiber nanofiltration membranes are prepared by applying two concentrations and various extrusion pressures according to the phase inversion method. Cross-sectional area and outer structures were characterized by using scanning electron microscope (SEM) and atomic force microscopy (AFM). In additional to the pore size distribution, either the mean roughness or the mean pore size of the PPSU hollow fiber surfaces was evaluated by AFM. It was found that the morphology of the PPSU fibers had both sponge-like and finger-like structures through different extrusion pressures and PPSU concentrations. The mean pore size and mean roughness for inner and outer surfaces were seen to be decreased with the increase of extrusion pressure at

Objective: Diarrhea is a symptom of a variety of conditions may attack the child. It considered one of
mam causes of mortality rates especially in low socio- economic level countries. The child can be
easily got dehydration and pass from loss of too much body fluid and due to the Common thoueht of
increasing the incidence of diarrhea during summer season, this study is done to find out the relation
between the high incidences rate of diarrhea and weather variation
Methodology: This survey conducted in AL- Markazi Child's Teaching Hospital for the year 2005 the
data were gathered from hospital records for the period (January - December) and age groups
taxonomy used by hospital applied. Descriptive statistical analysis

Worldwide, there is an increased reliance on COVID-19-related health messages to curb the COVID-19 outbreak. Therefore, it is vital to provide a well-prepared and authentic translation of English-language messages to reach culturally and linguistically diverse audiences. However, few studies, if any, focus on how non-English-speaking readers receive and linguistically accept the lexical choices in the messages translated into their language. The present study tested a sample of translated Arabic COVID-19-related texts that were obtained from the World Health Organization and Australian New South Wales Health websites. This study investigated to that extent Arabic readers would receive translated COVID-19 health messages and whether the t

Support vector machine (SVM) is a popular supervised learning algorithm based on margin maximization. It has a high training cost and does not scale well to a large number of data points. We propose a multiresolution algorithm MRH-SVM that trains SVM on a hierarchical data aggregation structure, which also serves as a common data input to other learning algorithms. The proposed algorithm learns SVM models using high-level data aggregates and only visits data aggregates at more detailed levels where support vectors reside. In addition to performance improvements, the algorithm has advantages such as the ability to handle data streams and datasets with imbalanced classes. Experimental results show significant performance improvements in compa

This paper focuses on the optimization of drilling parameters by utilizing “Taguchi method” to obtain the minimum surface roughness. Nine drilling experiments were performed on Al 5050 alloy using high speed steel twist drills. Three drilling parameters (feed rates, cutting speeds, and cutting tools) were used as control factors, and L9 (3³) “orthogonal array” was specified for the experimental trials. Signal to Noise (S/N) Ratio and “Analysis of Variance” (ANOVA) were utilized to set the optimum control factors which minimized the surface roughness. The results were tested with the aid of statistical software package MINITAB-17. After the experimental trails, the tool diameter was found as the most important facto