Geotechnical engineers have always been concerned with the stabilization of slopes. For this purpose,
various methods such as retaining walls, piles, and geosynthetics may be used to increase the safety factor of slopes prone to failure. The application of stone columns may also be another potential alternative for slope stabilization. Such columns have normally been used for cohesive soil improvement. Most slope analysis and design is based on deterministic approach i.e a set of single valued design parameter are adopted and a set of single valued factor of safety (FOS) is determined. Usually the FOS is selected in view of the understanding and knowledge of the material parameters, the problem geometry, the method of analysis and the

Concrete filled steel tube (CFST) columns are being popular in civil engineering due to their superior structural characteristics. This paper investigates enhancement in axial behavior of CFST columns by adding steel fibers to plain concrete that infill steel tubes. Four specimens were prepared: two square columns (100*100 mm) and two circular columns (100 mm in diameter). All columns were 60 cm in length. Plain concrete mix and concrete reinforced with steel fibers were used to infill steel tube columns. Ultimate axial load capacity, ductility and failure mode are discussed in this study. The results showed that the ultimate axial load capacity of CFST columns reinforced with steel fibers increased by 28% and 20 % for circular and square c

Acute myeloid leukemia is a malignant disease results from mutation in a multipotent haemopoietic stemcell. The study aimed to investigate NPM1 and FLT3-ITD mutations in Iraqi patients with AML and correlateresults with other clinical and laboratory findings. Fifty-eight AML patients, admitted to Baghdad TeachingHospital from October 2019 till March 2020 in addition to 25 normal controls, were included in the study.A detailed history, laboratory investigations including FLT3-ITD and NPM1 mutations were collected fromand analyzed. FLT3-ITD was detected in 17.24% of patients, NPM1 mutation in 10.34%. Most of thepatients are presented with pallor. FLT3-ITD mutation had a higher blast cell count (74%) while NPM1mutation had higher WBCs

Background: Ulcerative colitis (UC) is an inflammatory bowel disease restricted to the large intestine, characterized by superficial ulceration. It is a progressive and chronic disease requiring long-term treatment. Although its etiology remains unknown, it is suggested that environmental factors influence genetically susceptible individuals, leading to the onset of the disease. (C-X-C) ligand 9 is a chemokine that belongs to the CXC chemokine family, it plays a role in the differentiation of immune cells such as cytotoxic lymphocytes, natural killer T cells, and macrophages. Its interaction with its corresponding receptor CXCR3 which is expressed by a variety of cells such as effector T cells, CD8+ cytotoxic T cells, and macrophage

The present study aims to study the correlation between visfatin levels and metabolic syndrome in Iraqi obese adolescence (with and without metabolic syndrome) and its relation with other studied biochemical parameters. Sixty obese adolescences were depended in this study (with and without metabolic syndrome), compared with (30) non-obese children as control group. This study was done in the period from April 2020 until the end of December 2020, in the National Diabetes Centre/Mustansiriya University, Baghdad/Iraq. There were no significant differences in age, height, waist circumferences (WC), and diastolic blood pressure (DBP) in the patients' groups. In contrast, a significant increase differs (p<0.05) was recorded in the values of

Coupling reaction of 4-amino antipyrene with 2,6-dimethyl phenol gave bidentate azo ligand. The prepared ligand was identified by Microelemental Analysis, 1HNMR, FT-IR and UV-Vis spectroscopic techniques. Treatment of the prepared ligand with the following metal ions (CoII, NiII, CuII, ZnII, CdII, and HgII) in aqueous ethanol with a 1:2 M:L ratio and at optimum pH, yielded a series of neutral complexes of the general formula [M(L)2Cl2]. The prepared complexes were characterized using flame atomic absorption, (C.H.N) Analysis, FT-IR and UVVis spectroscopic methods as well as magnetic susceptibility and conductivity measurements. Chloride ion content was also evaluated by (Mohr method). The nature of the complexes formed were studied followin

Notwithstanding the importance of international cooperation as the other facet of international interactions, a strategy of conflict resolution, a maintainer of international peace and security, its provision in the United Nations conventions, as an objective of the United Nations after the international peace and security, however, the recognition of international cooperation has not been underlined by global, intellectual think tanks. While realism emphasized on the state's role in achieving international cooperation to ensure mutual and multilateral interests, liberalism focused on the role of international organizations in building such cooperation. Additionally, constructivist approaches developed other sub-variables to contribute to t

        In this study, Zinc oxide nanostructures were synthesized via a hydrothermal method by using zinc nitrate hexahydrate and sodium hydroxide as a precursor. Three different annealing temperatures were used to study their effect on ZnO NSs properties. The synthesized nanostructure was characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), Atomic force microscope (AFM), and Fourier Transform Infrared Spectroscopy (FTIR). Their optical properties were studied by using UV -visible spectroscopy. The XRD analysis confirms that all ZnO nanostructures have the hexagonal wurtzite structure with average crystallite size within the range of (30.59 - 34

This work deals with determination of optimum conditions of direct diffusion bonding welding of austenitic stainlesssteel type AISI 304L with Oxygen Free High Conductivity (OFHC) pure copper grade (C10200) in vacuum atmosphere of (1.5 *10^-5 mbr.). Mini tab (response surface) was applied for optimizing the influence of diffusion bonding parameters (temperature, time and applied load) on the bonding joints characteristics and the empirical relationship was evaluated which represents the effect of each parameter of the process. The yield strength of diffusion bonded joint was equal to 153 MPa and the efficiency of joint was equal to 66.5% as compared with hard drawn copper. The diffusion zone reveals high microhardness than coppe