It is clear that correct application of antibiotic prophylaxis can reduce the incidence of infection resulting from the bacterial inoculation in a variety of clinical situations; it cannot prevent all infections any more than it can eliminate all established infections. Optimum antibiotic prophylaxis depends on: rational selection of the drug(s), adequate concentrations of the drug in the tissues that are at risk, and attention to timing of administration. Moreover, the risk of infection in some situations does not outweigh the risks which attend the administration of even the safest antibiotic drug. The aim of this study was to compare between 2 prophylactic protocols in out patients undergoing oral surgical procedures. Thirty patients, selected from the attendants of oral surgery clinic in Al-Karamah Dental Center, were subjected to different oral surgical procedures under local anesthesia. These patients were given single dose antibiotic prophylaxis in 2 groups; 1st group were 15 patients given 1 million i.u. of procaine penicillin I.M. 30 minutes before oral surgery, 2nd group were 15 patients given 600mg clindamycin orally 1 hours before oral surgery. The maximum time for all procedures was 2 hours. There was no difference between procaine penicillin (1 million i.u.), and clindamycin (600mg), regimens concerning post operative infection in out patient’s oral surgical procedures. Key words: Antibiotic prophylaxis, outpatient oral surgery
<p>Mobility management protocols are very essential in the new research area of Internet of Things (IoT) as the static attributes of nodes are no longer dominant in the current environment. Proxy MIPv6 (PMIPv6) protocol is a network-based mobility management protocol, where the mobility process is relied on the network entities, named, Mobile Access Gateways (MAGs) and Local Mobility Anchor (LMA). PMIPv6 is considered as the most suitable mobility protocol for WSN as it relieves the sensor nodes from participating in the mobility signaling. However, in PMIPv6, a separate signaling is required for each mobile node (MN) registration, which may increase the network signaling overhead and lead to increase the total handoff latency
... Show MoreIdentification of complex communities in biological networks is a critical and ongoing challenge since lots of network-related problems correspond to the subgraph isomorphism problem known in the literature as NP-hard. Several optimization algorithms have been dedicated and applied to solve this problem. The main challenge regarding the application of optimization algorithms, specifically to handle large-scale complex networks, is their relatively long execution time. Thus, this paper proposes a parallel extension of the PSO algorithm to detect communities in complex biological networks. The main contribution of this study is summarized in three- fold; Firstly, a modified PSO algorithm with a local search operator is proposed
... Show MoreAcute myeloid leukemia is a malignant disease results from mutation in a multipotent haemopoietic stemcell. The study aimed to investigate NPM1 and FLT3-ITD mutations in Iraqi patients with AML and correlateresults with other clinical and laboratory findings. Fifty-eight AML patients, admitted to Baghdad TeachingHospital from October 2019 till March 2020 in addition to 25 normal controls, were included in the study.A detailed history, laboratory investigations including FLT3-ITD and NPM1 mutations were collected fromand analyzed. FLT3-ITD was detected in 17.24% of patients, NPM1 mutation in 10.34%. Most of thepatients are presented with pallor. FLT3-ITD mutation had a higher blast cell count (74%) while NPM1mutation had higher WBCs
... Show MoreA new scheme of plasma-mediated thermal coupling has been implemented which yields the temporal distributions of the thermal flux which reaches the metal surface, from which the spatial and temporal temperature profiles can be calculated. The model has shown that the temperature of evaporating surface is determined by the balance between the absorbed power and the rate of energy loss due to evaporation. When the laser power intensity range is 107 to108 W/cm2 the temperature of vapor could increase beyond the critical temperature of plasma ignition, i.e. plasma will be ignited above the metal surface. The plasma density has been analyzed at different values of vapor temperature and pressure using Boltzmann’s code for calculation of elec
... Show MoreIn this study the simple pullout concrete cylinder specimen reinforced by a single steel bar was analyzed for bond-slip behavior. Three-dimension nonlinear finite element model using ANSYS program was employed to study the behavior of bond between concrete and plain steel reinforcement. The ANSYS model includes eight-noded isoperimetric brick element (SOLID65) to model the concrete cylinder while the steel reinforcing bar was modeled as a truss member (LINK8). Interface element (CONTAC52) was used in this analysis to model the bond between concrete and steel bar. Material nonlinearity due to cracking and/or crushing of concrete, and yielding of the steel reinforcing bar were taken into consideration during the analysis. The accuracy of t
... Show MoreIraqi insurance market need to develop products and to find new insurance policies to cover the damages of the violence and political commotions dangers and to meet the needs of the proposers.
The global insurance companies recently issued such policies to pay the losses wich caused by the violent political acts of vandalism suffered by the property and investments wich estimated billions of dollars.
... Show MoreThis work presents an innovative approach to enhancing the performance of concrete with reclaimed asphalt pavement (RAP) aggregates using titanium dioxide (TiO2) nanoparticles. Traditional limestone coarse aggregates were partially replaced with 30% and 50% RAP aggregates; a subset of mixtures containing RAP aggregates was treated with TiO2 nanoparticles. The rheological, mechanical, and long-term properties of concrete, along with changes in its chemical composition following the addition of RAP and TiO2, were evaluated. Results revealed that using 30% and 50% RAP in concrete mixtures reduced their compressive strength by 18% and 27%, respectively. However, using TiO2 in those mixtures enhanced their compressive strength by 8.7% an
... Show More