Two quantitative, environment-friendly and easily monitored assays for Ni (II) and Co (III) ions analysis in different lipstick samples collected from 500-Iraqi dinars stores located in Baghdad were introduced. The study was based on the reaction of nickel (II) ions with dimethylglyoxime (DMG) reagent and the reaction of cobalt (III) ions with 1-nitroso-2-naphthol (NN) reagent to produce colored products. The color change was measured by spectrophotometric method at 565 nm and 430 nm for Ni and Co, respectively, with linear calibration graphs in the concentration range 0.25-100 mg L-1 (Ni) and 0.5-100 mg L-1 (Co) and LOD and LOQ of 0.11 mg L-1 and 0.36 mg L-1 (Ni), and 0.15 mg L-1 and 0.49 mg L-1 (Co). The UV/VIS data was compared to the results obtained by a novel microfluidic paper-based analytical device (µPAD) platform offering in-situ and cost-effect assay with a similar calibration graph with LOD and LOQ of 0.21 mg L-1 and 0.70 mg L-1 (Ni), and 0.22 mg L-1 and 0.75 mg L-1 (Co). The analysis of variance (ANOVA) indicated no significant difference between the UV/VIS, µPAD, and standard atomic absorption spectrometry (AAS) assay Ftab= 3.46 is much higher than FStat = 0.13 (Ni) and Ftab= 3.46 is much higher than FStat = 0.02 (Co). Also, a good correlation between results via the three methods was found. Thus, the µPAD platform offers a solid base for providing valuable information outside centralized laboratories.
Abstract
The current study aims to evaluate levels of metabolic hormones and lipid profile in a sample of growth hormone (GH) deficient patients. Seventy five GH deficient patients and twenty healthy subjects used as control group have been participated in this study during their attendance to the National Diabetic Center for Treatment and Research/Al-Mustansiriya University. The studied subjects’ ages were with a range (3-15 years). Blood samples were collected from the studied subjects to determine levels of basal GH, GH2 and GH3 after 1 hr and 1/30 hr provocation with clonidine, respectively; insulin like growth factor (IGF-1); levels of metabolic hormones [thyroid profile: triiodo
... Show MoreBeen investigating a Pfyrus antigen hepatitis pattern J and Virus-positive rubella viral hepatitis antibodies pattern J. declaration followed by the percentage rate-positive patients of measles Allmana antibodies
Bac kground:
Failure is the state or condition of not meeting a desirable or intended objective, and may be viewed as the opposite of success; students always have a question "Why did I get this grade. On the contrary success leads towards new sources of earning, in fact there are a lot of interacting factors play such extrinsic and extrinsic to reach success.
Objec t i ves :
To explore internal and external factors causing students failure in medical college and to reconnoiter factors improve academic performance.
Methods: A cross-sectional study, conducted in Al Kindy College of Medicine, for the period from November 8th 2012 to May 1st 2013. Formal ethical considerations were obtained about participation and methodology. A
In this current work, Purpose; to clearly the fundamental idea for constructing a design and
investigation of spur gear made of composite material its comes from the combination of (high
speeds, low noise, oil-les running, light weight, high strength, and more load capability)
encountered in modern engineering applications of the gear drives, when the usual metallic gear
cannot too overwhelming these combinations.
An analyzing of stresses and deformation under static and dynamic loading for spur gear tooth
by finite element method with isoparametric eight-nodded in total of 200 brick element with 340
nods in three degree of freedom per node was selected for this analysis. This is responsible for the
catastropic fa
This study was undertaken to prepare Nano zinc oxide (ZnO) by precipitation and microemulsion methods. Scanning electron microscopy (SEM), X-ray diffraction (XRD), FTIR spectrometry, atomic force microscopy (AFM), and Brunauer Emmett Teller (BET) surface area were the techniques employed for the preparation. The particle size of prepared nano ZnO was 69.15nm and 88.49nm for precipitation and microemulsion methods, respectively, which corresponded to the BET surface area 20.028 and 16.369m2/g respectively. The activity of prepared nano ZnO as a photocatalyst was estimated by the removal of ampicillin (Amp) under visible light. This study, therefore, examined the effect of pH in the range of 5-11, initial concen
... Show MoreBackground: The objective of this study was to investigate the possibility of standardizing the Bolton ratio analysis as a diagnostic measure for both Iraqi and Egyptian orthodontic populations within three Angle' classification groups. Materials and methods: Two hundred forty pretreatment study casts (one hundred twenty of each population) were included in this study and divided into three Angle' classification groups. The mesiodistal crown diameters of all teeth were measured for computing the anterior and total Bolton ratios. Analysis of variance was performed to compare the mean ratios of Bolton analysis as a function of the Angle classification.HSD test was used to specify the classes of malocclusion that have significant differences.
... Show MoreLeishmaniasis is a worldwide disease still treated with expensive compounds that present severe side effects, and are frequently ineffective emphasizing the importance to search effective compounds against this disease. Miltefosine drug (HePC) that used as antitumor agent has been used against Leishmania tropica in two forms promastigote and axenic amastigote in vitro conditions. Different concentrations (5, 10, 15, 20, 25 and 30 μM) of HePC were performed and exposed to both parasite forms in comparison to sodium stibogluconate (Sb) drug. Parasites viability then was determined using MTT assay after 12, 24, and 48hr of exposure. DNA was extracted from treated and untreated parasites after 48hr of exposure and qualitative analysis of th
... Show MoreIn current research Copper was employed for preparing a ternary system of Al–Si alloy in different (0.2–2.5 wt. %) the best was taken is (1.5%wt) of copper that circumstances of solidification for improving the mechanical performance of the available in aluminium alloy. Cast iron molds were prepared to obtain tensile strength testing specimens. Alloys were prepared by employing gas furnaces. The molten metal was poured into a preheated cast-iron mold. The obtained alloy structures were studied using an X-ray diffractometer and optical microscopy. The mechanical performance of the prepared alloys was examined under the influence of different hardening conditions in both heat and non-heat-treated conditions. The outcomes showed at the
... Show MoreAdsorption of AniLine and some derivatives from aqueous. solution on kaolin clays surface was investigated, The isotherms were of type S3 d S4 according to Giles Classification.
The effect of introducing electron withdrawing groups and
electron donating
Groups in the aromatic ring on the adsorption process has been investigated ; The results showed that the extent of adsorption has been increased as a
... Show MoreFour genetic populations ( P1 , P2 , F1 , F2) were used in this study .
The parental cross in barley ( P1 barakq and P2 Pakistan ) was done . Many quantitative
pheno types were estimated such as plants length , tillers number , grains yield , capsules
number , the number of grains per capsule and the weight of 1000 grains . The results showed
significant differences in genetic variance values in the seconed filial generation ( F2) for all
the studied phenotypes : High values for the heritability were observed for all the studied
phenotypes .
These results indicated the effect of additive and non-additive genes on the quantitative
phenotypes . Finally , the selection of first generation can utilized for impro