Five sites were chosen to the north of Babil Governorate in order to identify the limnological features and the impact of the Hindiya Dam during 2019. Site2 was located near the dam to reflect the ecological features of this site, whereas other sites, S1 was located at the upstream of the dam as a control site. Moreover, the two other sites S3 and S4 were located down the dam. The results of the study showed a close correlation between air and water temperature at all sites. Also there were significant differences in average of thirteen out of eighteen water parameters.Water temperature, total alkalinity, bicarbonate, DO, POS, TH and Mg+2 ions decreased from 22.76˚C, 203.33 mg/L, 146.75 mg/L, 8.8 mg/L, 100.023%, 438 mg/L, 35.55mg/L, respectively on S2 to 22.66 ˚C, 200.28 mg/L, 145.58 mg/L, 8.35 mg/L, 95.45%, 422.66 mg/L, 28.81 mg/L, respectively at site below the dam. While, turbidity, TSS, Ca+2, SO2+4, NO3-2 and PO4-2 increased from 13.32 NTU, 23.08 mg/L, 116.89 mg/L, 107.5 mg/L, 1.027 mg/L and 0.019 mg/L, respectively on S2 to 26.574 NTU, 26.83 mg/L, 119.23 mg/L, 137.5 mg/L, 1.145 mg/L and 0.032 mg/L, respectively at the site below the dam. However, no apparent dam effect was reported in EC, S, TDS, pH values at Euphrates River. No significant differences of all characteristics were found among sites except, turbidity, TSS, Mg+2, SO+4 and PO4-2. It can be considered that the Euphrates River is very hard, oligohaline, slightly alkaline, well ventilated and clear to turbid. In addition, the turbidity and TSS values exceeded permissible limits of water quality for aquatic life in most samples especially in site below the dam. However, the river was considered by BOD5 to be doubtful in its cleanliness water. Calcium, magnesium, nitrate and phosphate values in this study were within permissible limits.
Most reinforced concrete (RC) structures are constructed with square/rectangular columns. The cross-section size of these types of columns is much larger than the thickness of their partitions. Therefore, parts of these columns are protruded out of the partitions. The emergence of columns edges out of the walls has some disadvantages. This limitation is difficult to be overcome with square or rectangular columns. To solve this problem, new types of RC columns called specially shaped reinforced concrete (SSRC) columns have been used as hidden columns. Besides, the use of SSRC columns provides many structural and architectural advantages as compared with rectangular columns. Therefore, this study was conducted to explain the structura
... Show MoreLeishmania parasites reproduce wherever there are cells of the mononuclear phagocyte system, almost in macrophages. These are most copious in the liver and spleen;therefore, infection leads to an expansion of both of them. This study determined the burden of visceral leishmaniasis (VL) infection on liver and spleen. A total of 20 mice were infected peritoneally with 2x107promastigotes of Leishmania donovani / ml and other 12 mice left without infection as a healthy control. The weight of whole body, liver and spleen were measured and the histological development using hematoxylin and eosin stains were determined after 15, 30, 45-and 60-days post infection. The results represent that the mean weights of liver and spleen were increased in inf
... Show MoreSustainable crop production in a coarse soil texture is challenging due to high water permeability and low soil water holding capacity. In this paper, subsurface water retention technology (SWRT) through impermeable polyethylene membranes was placed at depth 35 cm below ground surface and within the root zone to evaluate and compare the impact of these membranes and control treatment (without using the membranes) on yield and water use efficiency of eggplant inside the greenhouse. The study was conducted in Al-Fahamah Township, Baghdad, Iraq during spring growing season 2017. Results demonstrated the yield and water use efficiencies were 3.483 kg/m2 and 5.653 kg/m3, respectively for SWRT treatment p
... Show MoreThis study investigated the structural behavior of a beam–slab member fabricated using a steel C-Purlins beam carrying a profile steel sheet slab covered by a dry board sheet filled with recycled aggregate concrete, called a CBPDS member. This concept was developed to reduce the cost and self-weight of the composite beam–slab system; it replaces the hot-rolled steel I-beam with a steel C-Purlins section, which is easier to fabricate and weighs less. For this purpose, six full-scale CBPDS specimens were tested under four-point static bending. This study investigated the effect of using double C-Purlins beams face-to-face as connected or separated sections and the effect of using concrete material that contains different recycled
... Show MoreThe hydrodynamics behavior of gas - solid fluidized beds is complex and it should be analyzed and understood due to its importance in the design and operating of the units. The effect of column inside diameter and static bed height on the minimum fluidization velocity, minimum bubbling velocity, fluidization index, minimum slugging velocity and slug index have been studied experimentally and theoretically for three cylindrical columns of 0.0762, 0.15 and 0.18 m inside diameters and 0.05, 0.07 and 0.09 m static bed heights .The experimental results showed that the minimum fluidization and bubbling velocities had a direct relation with column diameter and static bed height .The minimum slugging velocity had an
... Show MoreThe main function of a power system is to supply the customer load demands as economically as possible. Risk criterion is the probability of not meeting the load. This paper presents a methodology to assess probabilistic risk criteria of Al-Qudus plant before and after expansion; as this plant consists of ten generating units presently and the Ministry Of Electricity (MOE) is intending to compact four units to it in order to improve the performance of Iraqi power system especially at Baghdad region. The assessment is calculated by a program using Matlab programming language; version 7.6. Results show that the planned risk is (0.003095) that is (35 times) less than that in the present plant risk; (0.1091); which represents respectable imp
... Show MoreUnlike welding, soldering does not involve melting the work pieces. Soldering is a process in which two or more items are joined together by melting and putting a filler metal (solder) into the joint. Failure in the solder joint may make the system components lose their functions. Electrical wiring and electronic components are joined to devices and printed circuit boards using soldering. Soldering and brazing are both used in the assembly of musical instruments. Lead-tin alloy solder employed in the current investigation which has a diameter of 4 mm and a density of 11.0103 kg/m3 with continuous heat flux heating from the domain's left side and complete insulation on the other side. The melting of PCM was simulated using the ANSYS
... Show More