2 - 5,5 cm mosquito fishes (Gambusia affinis) were collected from brooks of Baghdad university . This study aimed to identify the histological structure and embryonic development of the gas bladder . The results revealed that the gas bladder of the adult fish consists of single chamber, paraphysoclistous , and its wall consist of three layers. The primordium of the gas bladder appears in 2,5 mm fish embryo as an evagination from the right side of endoderm of foreguts wall. This primordium consists of two thecae, inner, is simple columnar epithelium and outer originates from undifferentiated mesoderm. Simultaneously with the appearance of gas gland in the ventral side of the sac in 4 mm embryo, morphological and histological chan

Thin films of In2O3-CdO at various CdO contents (0.01, 0.02, 0.03, 0.04 and 0.05) were deposited on transparent substrate which is glass using chemical spray pyrolysis deposition method at substrate temperature 150oC. The structural properties was studied to characterize the prepared materials by XRD analysis. Surface morphology has been illustrated using scanning electron microscopy which proved the nanosize of prepared materials. This materials have been used as gas sensor for toxic gas which is hydrogen sulfide H2S. The sensitivity and response speed have been investigated with addition of CdO nanoparticles. © 2021, S.C. Virtual Company of Phisics S.R.L. All rights reserved.

The adsorption isotherms and kinetic uptakes of CO₂ were measured. Adsorption isotherms were measured at two temperatures 309 K and 333 K and over a pressure range of 1 to 7 bar. Experimental data of CO₂ adsorption isotherms were modeled using Langmuir, Freundlich and Temkin. Based on coefficient of correlation it was found that Langmuir isotherm model was well suited with the experimental data of CO₂ adsorption isotherms.  In addition, Adsorption kinetic of CO₂ mixture with N₂ containing 10 % by volume CO₂ and 90 % by volume N₂ were determined in a temperature 36 °C and under the atmospheric pressure .When the flow rate was increased from

ءأرﻘﻟا ةﺎﯾﺣﺑ ًﺎﻘﯾﺛو ًﻻﺎﺻﺗا لﺻﺗﺗ. نﻣ ﮫﺑﺗﺎﮐﻟﻟ ﻲﺻﺧﺷﻟا ﻊﺑﺎطﻟا ﻲﻔﺣﺻﻟا دوﻣﻌﻟا لﻣﺣﯾ ا فﻟﺗﺧﻣﻟ ﮫﻟوﺎﻧﺗ لﻼﺧ وا ﮫﺋارا وا هرظﻧ ﺔﮭﺟو لﻣﺣﺗ ﻲﺗﻟا ﺔﯾﻣوﯾﻟا ثادﺣﻻاو ﺎﯾﺎﺿﻘﻟ ﺢﺿﻔﺑ موﻘﯾو ثادﺣﻻاو ﺔﯾﺑﻟﺳﻟا رھاوظﻟﻟ ىدﺻﺗﯾ وا، ءيرﺎﻘﻟا ﯽﻟا ﮫﺑرﺎﺟﺗ وا هرﺎﮐﻓا ءﺎطﺧﻻا دﺻرﯾ بﯾﻗرﺑ ﮫﺑﺷا وھو، ءيرﺟﻟا دﻘﻧﻟا نﻋ مﻧﯾ بوﻟﺳﺎﺑ ﺔﺋطﺎﺧﻟا تﺎﺳرﺎﻣﻣﻟا ﺎﮭﺣدﻣﯾو تﺎﯾﺑﺎﺟﯾﻻا ﯽﻟﻋ

The wear behavior of alumina particulate reinforced A332 aluminium alloy composites produced by a stir casting process technique were investigated. A pin-on-disc type apparatus was employed for determining the sliding wear rate in composite samples at different grain size (1 µm, 12µm, 50 nm) and different weight percentage (0.05-0.1-0.5-1) wt% of alumina respectively. Mechanical properties characterization which strongly depends on microstructure properties of reinforcement revealed that the presence of ( nano , micro) alumina particulates lead to simultaneous increase in hardness, ultimate tensile stress (UTS), wear resistances. The results revealed that UTS, Hardness, Wear resistances increases with the increase in the percentage of

The aim of this research does not deal with evaluation occurs at any points in the design of the plan alternatives themselves or formulation of goals and objectives. The aim of this research is that test and evaluate the fully alternatives. We can therefore state as the principle that evaluation of alternative plans must be based on attempts to show how far each plan satisfies all the objectives are expressed as specification of the performance of the urban and regional system. The planner can submit the result (as in the traditional way) for each alternative, with particular reference to the weighting of objectives. The summery result can be presented and the preferred plan indicated that with largest index of Goals-achievement.

Abstract  

The aim of this paper is to investigate and discuss the mechanisms of corrosion of epoxy coatings used for potable water tanks. Two distinct types of Jotun epoxy coatings: Tankguard 412 contained polyamine cured epoxy and Penguard HB contained polyamide cured epoxy, were tested and studied using the electrochemical impedance spectroscopic (EIS) method. The porosity of epoxy coatings was determined using EIS method. The obtained results showed that the two epoxy coatings have excellent behavior when applied and tested in potable water of Basrah city. Polyamine is more resistance to water corrosion compared to polyamide curing epoxy and has high impedance values. Microscopic inspection after te