his study aimed to investigate the usability of Recycled Concrete Aggregate (RCA) in warm mix asphalt (WMA) as the implementation of sustainable construction technology. Five replacement rates (0%, 25%, 50%, 75%, and 100%) were tested for the coarse fraction of virgin aggregate (VA) with 3 types of RCA: untreated RCA, HL-treated RCA, and HCL-treated RCA. Scanning electron microscopy (SEM) analyses were performed to investigate the surface morphology for both treated and untreated RCA. The optimum asphalt cement content for every substitution rate was determined using Marshall mix design method. Thereafter, asphalt concrete specimens were prepared using the optimum asphalt cement content, followed by the evaluation of their performance prope

The performance of photovoltaic (PV) panel having staggered metal foam fins was examined experimentally in Baghdad, Iraq. Three staggered metal foam fin configurations attached to the backside of the PV panel were studied. The measured parameters were front and back surfaces temperature, open voltage and current circuits, maximum power, and PV efficiency. It was noted that the maximum electrical efficiency enhancement was 4.7% for staggered metal foam fins (case III) than the reference PV panel. The operating temperature of the cell was increased when the value of solar intensity was high. Thereby, the electrical efficiency was decreased. It was found that the metal foam fins decreased the PV temperature by 2-3 ^o

Industrial development has recently increased, including that of plastic industries. Since plastic has a very long analytical life, it will cause environmental pollution, so studies have resorted to reusing recycled waste plastic (sustainable plastic) to produce environmentally friendly concrete (green concrete). In this research, producing environmentally friendly load-bearing concrete masonry units (blocks) was considered where five concrete mixtures were compressed at the blocks producing machine. The cement content reduced from 400 kg/m³ (B-400) to 300 kg/m³ (B-300) then to 200 kg/m³ (B-200). While (B-380) was produced using 380 kg/m³ cement and 20 kg/m³ nano-sil

In this work, nanostructure zinc sulfide (ZnS) thin films at temperature of substrate 450 oC and thickness (120) nm have been produced by chemical spray pyrolysis method. The X-Ray Diffraction (XRD) measurements of the film showed that they have a polycrystalline structure and possessed a hexagonal phase with strong crystalline orientation of (103). The grain size was measured using scanning electron microscope (SEM) which was approximately equal to 80 nm. The linear optical measurements showed that ZnS nanostructure has direct energy gap. Nonlinear optical properties experiments were performed using Q-switched 532 nm Nd:YAG laser Z-scan system. The nonlinear refractive index (n2) and nonlinear absorption coefficient (β) estimated for Z

Objective:This study aimed to identify the effect of restricted training on some motor abilities and offensive skills of youth football players under 19 years old Research methodology:The researchers used the experimental method with two equivalent groups (experimental and control). The research sample consisted of 26 players from Al-Zawraa Sports Club (U-19), divided into an experimental group (13 players) and a control group (13 players). The experimental group performed a restricted training program for eight weeks, with three training sessions per week, while the control group continued with the regular training program. Several tests were used to measure the study variables, including the Ronaldo Speed Test (dribbling and shoot

The rapid spread of the COVID-19 coronavirus in 2019 infected many people, primarily affecting the respiratory system. Both COVID-19 and type 2 diabetes have been associated with numerous risks that have become life-threatening. The study studied the link between galectin levels and some clinical characteristics in Iraqis with type 2 diabetes and COVID-19 against those without diabetes. The study included 120 patients and healthy men. Three groups were formed for this study depending on the initial mutant cell line: 80 samples of individuals with type 2 diabetes, aged 40–60 years, with and without COVID-19, were included in each of the first and second groups. The control group consisted of 40 research participants who were matched for ag

The rapid spread of the COVID-19 coronavirus in 2019 infected many people, primarily affecting the respiratory system. Both COVID-19 and type 2 diabetes have been associated with numerous risks that have become life-threatening. The study studied the link between galectin levels and some clinical characteristics in Iraqis with type 2 diabetes and COVID-19 against those without diabetes. The study included 120 patients and healthy men. Three groups were formed for this study depending on the initial mutant cell line: 80 samples of individuals with type 2 diabetes, aged 40–60 years, with and without COVID-19, were included in each of the first and second groups. The control group consisted of 40 research participants who were matched for ag

Background: Determination of local bone mineral density (BMD) immediately after implant insertion play an important role in implant success rate, may offer comprehensive description of the bone, and give enough information to the surgeon prior to implant insertion and at follow up status. The aim of the present study is to evaluate the changes of local bone density in the dental implant recipient sites by using computerized tomography. Material and method: The sample consisted of (20) dental implants recipient sites, bone density assessment was done twice, immediately after implants insertion and after six months. Results: The mean HU of the bone around the implant insertion site, immediately after implant placement was 552.28 HU, and inc

Background: Contact between implant material and bones must be strong and fast creation, to fulfill these properties appropriate surface modifications must apply on used implants. In this contribution; double surface modifications are applied on Ti-6Al-4V alloy to accelerate osseointegration. Materials and methods: Anodic process is utilized to create titania nanotubes (TNTs) on the screws made from Ti-6Al-4V alloy. These implants were coated with nano ZrO2 particles. Second modification was annealing anodized screws at 8000C, and implanted in tibiae of nine adult New Zealand white rabbits. Results: Physical and histological consequences of two surface modifications on Ti-6Al-4V alloy screws were studied. Scanning electron microscope (SEM)