Today’s world confronts various threats from different sources. Similar to deprivation of energy, economic facilities, or political deposition, educational poisoning is one of the dangerous phenomena that result from distorting and corrupting the ethical and educational components of teaching by various material and non – material means.This paper sheds light on the concept of the educational system which is not a mere process of teaching, but rather an endless process of socialization that begins in the family and develops into religious, ethical, scientific and mythological systems, all of which form the cognitive component. It also defines the necessary means by which it is transmitted from one generation into another. The educati

Changes in mechanical properties of material as a result of service in different conditions can be provided by mechanical testing to assist the estimation of current internal situation of these materials, or the degree of deterioration may exist in furnaces serviced at high temperature and exceed their design life. Because of the rarity works on austenitic stainless steel material type AISI 321H, in this work, ultimate tensile strength, yield strength, elongation, hardness, and absorbed energy by impact are evaluated based on experimental data obtained from mechanical testing. Samples of tubes are extracted from furnace belong to hydrotreaterunit, also samples from un-used tube material are used to make comparisons between these properti

The present research aims to study the effect of friction stir welding (FSW) parameters on temperature distribution and tensile strength of aluminum 6061-T6. Rotational and traverse speeds used were (500,1000,1400 rpm) and (14,40,112 mm/min) respectively. Results of mechanical tests showed that using 500rpm and 14mm/min speed give the best strength. A three- dimensional fully coupled thermal-stress finite element model via ANSYS software has been developed. The Rate dependent Johnson-Cook relation was utilized for elasto-plastic work deformations. Heat-transfer is formulated using a moving heat source, and later used the transient temperature outputs from the thermal analysis to determine equivalent stresses in the welde

In this work, the effects of solvent properties on the characteristics of absorption and fluorescence for two laser dyes was studied. Dyes used in this work include Coumarin 5400 and DCM, while the solvents include ethanol, methanol, acetone, propanol and chloroform. Coumarin 5400 dye shows sharp fluorescence peaks in the green band of visible region while the DCM dye shows relatively wide band within 590-630 nm. Therefore, the selection of any dye for random gain medium applications should be performed after determining the most appropriate solvent as the optimum fluorescence characteristics are obtained.

The aim of this study is to compare the effects of three methods: problem-based learning (PBL), PBL with lecture method, and conventional teaching on the understanding of thermodynamics, group work and self-directed learning skills among physics undergraduates. The actual sample size comprises of 122 students, who were selected randomly from the Physics Department, College of Education in Iraq, for academic year 2011-2012. In this study, the pre and posttest were done and the instruments were administered to the students for data collection. Inferential statistics were employed to analyze data. The independent variables were the PBL, the PBL with lecture method, and the conventional teaching. Dependent variables of statistical analysis were

This research aims to study the effect of microwave furnace heat on the mechanical properties and fatigue life of aluminum alloy (AA 2024-T3). Four conditions were used inside microwave furnace (specimens subjected to heat as dry for 30 and 60min. and specimens subjected to heat as wet (water) for 30 and 60 min.), and compared all results with original alloy (AA 2024-T3). Tensile, fatigue, hardness and surface roughness tests were used in this investigation. It is found that hardness of dry conditions is higher than wet conditions and it increases with increasing of time duration inside microwave furnace for dry and wet conditions. Also, tensile strength has the same behavior of hardness, but it increases with decreasing

The current study examines the combined impacts of ultrasonic waves and nano silica (NS) on reducing the viscosity Sharqy Baghdad heavy crude oil with an API gravity of 20.32. NS of an average particle size of 59.93 nm and 563.23 m²/g surface area were produced utilizing the sol-gel technique from Iraqi sand. The XRD analysis indicates the existence of an amorphous silica, the SEM analysis showed that NS tends to agglomerate, and the FTIR spectra exhibited the presence of siloxane and silanol groups. In addition, the TGA analysis demonstrated a total weight loss of 15.62%, validating the thermal stability of the NS. The experiments included a study of the impact of ultrasonic power, exposure time, duty cycle, temperature, and the c

Background: Nutrition can affect periodontal disease through contributing to microbial growth in the gingival crevice, affecting the immunological response to bacterial antigens and assisting the repair mechanism of the connective tissue at the local site after injury from plaque and calculus. The aim of this study was to assess the prevalence of Oral hygiene (plaque and calculus) and gingivitis in relation to age, gender and nutritional status. Materials and methods: The sample included (444) kindergarten children at age of (4 and 5 years old) males and females from urban areas in Al-Ramadi city. The assessment of nutritional status was performed using anthropometr

Background: Dental caries is the most common oral problem, although dental caries is not life threating, it has aharmful effect on quality of life. Socioeconomic factors were found to be strong predictors of the prevalence of oral diseases in children, likes family income, occupational prestige, and education. The aim of this study is to assess the effect of socioeconomic factors on occurrence dental caries in their children. Materials and methods: The sample consists of 550 kindergartens children aged between (4-5) years were selected randomly, girls and boys. The kindergartens selection was randomly from different geographical areas in Al-Najaf governorate. Information was taken from children's parents using questionnaire with the help o