Binary mixtures of three, heavy oil-stocks was subjected to density measurements at temperatures of 30, 35 and 40 °C. and precise data was acquired on the volumetric behavior of these systems. The results are reported in terms of equations for excess specific volumes of mixtures. The heavy oil-stocks used were of good varity, namely 40 stock, 60 stock, and 150 stock. The lightest one is 40 stock with °API gravity 33.69 while 60 stock is a middle type and 150 stock is a heavy one, with °API gravity 27.74 and 23.79 respectively. Temperatures in the range of 30-40 °C have a minor effect on excess volume of heavy oil-stock binary mixture thus, insignificant expansion or shrinkage is observed by increasing the temperature this effect becomes more significant although the heavy oil-stocks is spiked with hydrocarbons like (gas oil, toluene and reformate). Blending of Heavy oil-stocks with hydrocarbons spikes (gas oil, toluene and reformate) form non-ideal mixtures, for which excess volume can be positive or negative depending on nature species. Spiking of Heavy oil-stocks with either gas oil or reformate resulted in negative excess volume. This shrinkage is greater for the lowest boiling point spike as in the case of reformate, While, the presence of methyl groups in aromatic rings results in a positive excess volume, as shown in toluene when blended with 40 stock but a negative excess volume was found when blended with 60 stock and 150 stock. The API gravity of heavy oil-stocks has an effect on excess volume when the oil-stocks spiked with hydrocarbons like (gas oil, toluene and reformate). This 40 stocks as a typical light types resulted in minimum negative excess volume of -0.47 at 30 °C, when it was spiked with the gas oil; while the spiked heavy oil-stock with kerosene shows a maximum excess volume of -15.56 at 40 °C.
The present research aims to study the effect of friction stir welding (FSW) parameters on temperature distribution and tensile strength of aluminum 6061-T6. Rotational and traverse speeds used were (500,1000,1400 rpm) and (14,40,112 mm/min) respectively. Results of mechanical tests showed that using 500rpm and 14mm/min speed give the best strength. A three- dimensional fully coupled thermal-stress finite element model via ANSYS software has been developed. The Rate dependent Johnson-Cook relation was utilized for elasto-plastic work deformations. Heat-transfer is formulated using a moving heat source, and later used the transient temperature outputs from the thermal analysis to determine equivalent stresses in the welde
... Show MoreThe study was designed in the northwestern part of Karbala city for the purpose of knowing the efficiency of some plant species of trees and shrubs planted by the municipality of the city to contribute to the deposition of dust particles suffered by the city's environment, in particular, as well as its ability to accumulate heavy metals in dust or soil, and to consider the study model for application in different parts of Iraq. It was found that the plant species (Acacia , Eucalyptus , Clkonukiyrs and Dodenia) in the studied area that were given the symbols (A,B,C and D respectively). Used the method of calculating the leaf area index to calculate the amount of dust drawn by the stock plant, then chemical digestion dry
... Show More
(1)
(1)
The current study aims to assess the water quality of the Al-Diwaniyah River in the city of Al-Diwaniyah to drink in terms of chemical properties and heavy metals and their impact on the health of the local population. The results showed that most of the parameters in the river water are of low concentrations due to the limited human activities in polluting the river water. The study concluded that the water quality is suitable for drinking depending on major cations and anions in all seasons. The Heavy Metal Pollution Index (HPI) showed that the river water was clean and safe, except two slightly polluted samples. The study concluded that river water for drinking or various domestic uses does not pose any danger to human heal
... Show More
(1)
Concentrations of four heavy metals, Zinc , Copper , Lead and Cadimium were determed in water and sediment samples collected bi-weekly from six sampling sites on the lower part of River Diyala during low flow period (August to October) and high flow period (April to June). A reference point site (1) was situated upstream the effects of the effluent. Present work describes the e
... Show MoreSmoking-related diseases can be attributed to the inhalation of many different toxins, including heavy metals, which have a host of harmful health effects. The primary objective of this study was to determine whether local and imported cigarette brands used in Iraq , have they elevated levels of metals or not .Three metals Lead (Pb) , Cadmium (Cd) and Chromium(Cr) were determined in tobacco of seventeen brands of imported cigarettes commonly available in Iraq and three Iraqi domestic cigarettes , which were randomly taken from retail market in Baghdad by using flame atomic absorption spectrometry. The produced data of imported and local cigarette brands were discussed and compared together and with studies from elsewhere .The result
... Show More
(9)
(6)
The objective of this study is to select a suitable observing region at Baghdad location (44o 22' 48", 33o 16' 30") with low interference that may affect frequency of 1.42 GHz. Baghdad University Radio Telescope (BURT) is used in this study to determine a convenient region for observation in Baghdad sky. Different azimuths and elevations were chosen at different observations time. The results of this study showed that the best observations regions were located at azimuth (120o-160o) and (210o-260o). These regions included less sky temperature and estimated to be (42.8 to 163) K. The sky temperature model could be represente
... Show More
(2)
(2)
been taken at room temperature down to liquid nitrogen temperature (77K). Polar and nonpolar solvents have been used to study the solvent effect on the absorption and fluorescence spectra of solute molecules. Some of the spectroscopic parameters have been determined as functions of solvent polarity and temperature. The results indicate that the band width FWHM increases with increasing the solvent polarity and temperature, while the peak emission cross section decreases with increasing of solvent polarity and decreases with increasing the temperatures. Clear vibrational structure spectra of benzoanthracene molecules have been observed in Nonane and Hexane solvents at 77K.
(7)