A real method of predication brake pad wear ,could lead to substantiol economies of time and money. This paper describes how such a procedure has been used and gives the results to establish is reliability by comparing the predicted wear with that which actually occurs in an existing service. The experimental work was carried out on three different commercial samples ,tested under different operation conditions (speed,load,time...etc)using a test ring especially modified for this purpose. Abrasive wear is mainly studied , since it is the type of wear that takes place in such arrangements. Samples wear tested in presences of sand or mud between the mating surfaces under different operational conditions of speed, load and braking time .Mechanical properties of the pad material samples (hardness, young,s modulus and collapse load under pure bending condition )wear established . The thermal conductivity and surface roughness of the pad material wear also found in order to enable comparison between the surface condition before and after testing. Sliding velocity had a small effect on the wear rate but it had great effect on friction coefficient. Wear rate was affected mainly by the surface temperature which causing a reduction friction coefficient and increasing the wear rate. Surface roughness had almost no effect on the wear rate since it was proved experimentally ,that the surface becomes softer during operation .mechanical properties of the pad material had fluctuating effect on wear rate. The existence of solid particles between pad and disc increasing wear rate and friction coefficient while the mud caused a reduction in wear rate of the pad surface since it acts as a lubricant absorbing the surface heat generated during sliding the area of contact between pad and disc. wear rate obtained experimentally agreed fairly well that found from empirically obtained equations.
This research dealt with the impact of internal control on tax performance using balanced scorecard indicators because of its special importance in improving tax performance and reform. The internal control system is a safety valve for senior management in all organizations, it plays an important role in the regularity and development of work and the fight against corruption To provide reliable and accurate data and information, follow up on compliance with laws, regulations and instructions. The aim of this research is to demonstrate how control affects tax performance and how to adapt internal control components to improve tax performance. In the General Authority for taxes and its branches,. The research resulted in a number of conclu
... Show MoreTo observe the effect of media of the internal pressure on the equivalent stress distribution in the tube, an experimental study is done by constructing a testing rig to apply the hydraulic pressure and three dies are manufactured with different bulging configurations (square, cosine, and conical). In the other part, ANSYS APDL is generated to analyze the bulging process with hydraulic and rubber (natural and industrial) media. It was found that when the media is a rubber, the stress is decreased about 9.068% in case of cosine die and 5.4439% in case of conical die and 2.8544% in case of square die. So, it can be concluded that the internal pressure in the rubber media is much better than in hydraulic media. Also, the force needed for fo
... Show More
The love of the world and its lusts are the head of sins and the corruptors of religion, and the one who loves and loves them who prefers them over the hereafter is one of the most pitiful of creation, and the least intelligent of them, as he prefers imagination over reality, sleep over wakefulness, fleeting shadow over eternal bliss and the mortal abode over the eternal abode, and he sold the life of eternity for the most luxurious life. In life, it is dreams and sleep or as a fleeting shadow, and as it was said: The intelligent person is not deceived.
The reason for choosing this topic is due to two things:
The first: When I contemplated the reasons for the differences and conflicts that afflicted our wounded and occupied country
النظام السياسي اليمني : دراسة في المتغيرات الداخلية
Praise be to God, Lord of the worlds, and prayers and peace be upon our master Muhammad and his family and companions until the Day of Judgment.
The words of God Almighty are for the sake of the greatest and greatest speech, and the scholars, may God have mercy on them, raced.
To dive into knowing the word of God and what he intended, so they wrote in it the literature and collected works in it, and explained it to those after them.
And when the noble companions, were extremely eloquent and eloquent, because the Holy Qur’an was revealed in the language of the Quraysh, and all the Arabs knew their language, they understood the Holy Qur’an and applied it p
The present study aims at analyzing the polysemy of the English preposition in from the cognitive linguistic (CL) point of view using Evans' and Tyler's approach (2003). The perplexity faced by Iraqi second language learners (L2) due to the multi-usages of this preposition has motivated the researcher to conduct this study. Seventy-six second year university students participated in this experimental study. The data of the pre-test and post-test were analyzed by SPSS statistical editor. The results have shown the following: First, a progress of more than (0.05≤) has been detected as far as students' understanding of the multiple usages of the preposition in is concerned. Second, the results of the questionnaire have s
... Show MoreMarriage is a holly secret in Christian religion .So it id natural that its ceremonies acquired religious form .In general the marriage is contracted by minister of religion in presence of the two parties or by a proxy or presence of parents if it is necessary . And to make the condition of publicity for the marriage ,its procedures must be made before witnesses .Also the minister of religionhave to confirm the agreement of the two parties before beginning the procedures.The marriage ceremonies are made.These procedures are religious traditions that includes praying and make blessings and putting the rings in fingers by thepriest . The marriage is a holly secret performed by the crown pray according to the church religious traditions
Christianity has rituals and rituals to be carried out, and can not be abandoned, and they see that the sacred statutes ordered by Christ () his followers, including: (the mystery of baptism between Christian denominations, descriptive study) A Christian is to be baptized as the seal of faith, as evidenced by the Bible in the words of Jesus to His disciples.
Baptism takes place in the name of the Father, the Son, and the Holy Spirit. This makes them Christian through the practice of this obligatory man enters the Church, represented by the death, burial, and resurrection of Christ according to their belief. And every person who has received the sacrament of baptism remains a Christian until death, in the light of what they see.
Background: The isthmus is a difficult area in the root canal complex to manage. The research aimed to evaluate the efficiency of three different obturation techniques (lateral condensation, EandQ (thermoplasticized gutta percha system) and Soft Core (thermoplasticized core carrier gutta percha system)) to obturate the isthmus area of roots prepared by two different instrumentation techniques (rotary ProTaper universal and ProTaper Next systems). Material and method: Sixty freshly extracted teeth were randomly divided into two main groups (A and B) of 30 teeth each. Group A was prepared by rotary ProTaper Universal whereas group B was prepared by ProTaper Next system. Each main group was then randomly subdivided into three subgroups of 10 t
... Show More
Background: The success and maintenance of indirect dental restorations is closely related to the marginal accuracy, which is affected by many factors like preparation design, using of different fabrication techniques, and the time of taking final impression and pouring it. The purpose of this in vitro study was to evaluate the effect of different pouring time of conventional impression on the vertical marginal gap of full contour zirconia crowns in comparison with digital impression technique. Materials and Methods: Forty sound recently extracted human permanent maxillary first premolar teeth of comparable size and shape were collected. Standardized preparation of all teeth samples were carried out to receive full contour zirconia crown re
... Show More