A real method of predication brake pad wear ,could lead to substantiol economies of time and money. This paper describes how such a procedure has been used and gives the results to establish is reliability by comparing the predicted wear with that which actually occurs in an existing service. The experimental work was carried out on three different commercial samples ,tested under different operation conditions (speed,load,time...etc)using a test ring especially modified for this purpose. Abrasive wear is mainly studied , since it is the type of wear that takes place in such arrangements. Samples wear tested in presences of sand or mud between the mating surfaces under different operational conditions of speed, load and braking time .Mechanical properties of the pad material samples (hardness, young,s modulus and collapse load under pure bending condition )wear established . The thermal conductivity and surface roughness of the pad material wear also found in order to enable comparison between the surface condition before and after testing. Sliding velocity had a small effect on the wear rate but it had great effect on friction coefficient. Wear rate was affected mainly by the surface temperature which causing a reduction friction coefficient and increasing the wear rate. Surface roughness had almost no effect on the wear rate since it was proved experimentally ,that the surface becomes softer during operation .mechanical properties of the pad material had fluctuating effect on wear rate. The existence of solid particles between pad and disc increasing wear rate and friction coefficient while the mud caused a reduction in wear rate of the pad surface since it acts as a lubricant absorbing the surface heat generated during sliding the area of contact between pad and disc. wear rate obtained experimentally agreed fairly well that found from empirically obtained equations.
Numerous integral and local electron density’s topological parameters of significant metal-metal and metal-ligand bonding interactions in a trinuclear tetrahydrido cluster [(Cp* Ir) (Cp Ru)2 (μ3-H) (μ-H)3]1 (Cp = η5 -C5Me5), (Cp* = η5 -C5Me4Et) were calculated and interpreted by using the quantum theory of atoms in molecules (QTAIM). The properties of bond critical points such as the delocalization indices δ (A, B), the electron density ρ(r), the local kinetic energy density G(r), the Laplacian of the electron density ∇2ρ(r), the local energy density
... Show More
(4)
(1)
A novel ligand, (E)-5-((2-hydroxy-4,6-dimethylphenyl)diazenyl)-2,3-dihydrophthalazine-1,4- dione, was synthesized through the reaction of 3,5-dimethylphenol with the diazonium salt of 5-amino-2,3-dihydrophthalazine-1,4-dione. The ligand underwent characterization through the utilization of diverse spectroscopic methods, including UV-Vis, FT-IR, 13C, and 1H-NMR, alongside Mass spectroscopy and micro elemental analysis (Carbon, Hydrogen, Nitrogen, and Oxygen). Metal chelates of transition metals were prepared and analyzed using elemental analysis, mass spectra, atomic absorption, UV-Vis, FT-IR spectral analysis, as well as conductivity and magnetic measurements. The investigation into the compounds’ nature was conducted by utilizing mole r
... Show MoreOur work included a synthesis of three new imine derivatives—1,3-thiazinan-4-one, 1,3-oxazinan-6-one and 1,3-oxazepin-4,7-dione—which contained an adamantyl fragment. These were produced via the condensation of the Schiff`s base (E)-N-(adamantan-1-yl)-1-(3-aryl)methanimine with 3-mercaptopropanoic acid; 3-chloropropanoic acid; and maleic, citraconic anhydride, respectively. These new imines were prepared via the condensation of adamantan-1-ylamine and 3-nitro-, 3-bromobenzaldehyde in n-BuOH. We obtained a good yield of products. FTIR, 1H NMR spectroscopy and C.H.N.S analysis were used to diagnostic the products. The molecular structure of (E)-N-(adamantan-1-yl
... Show More
(5)
(1)
To observe the effect of media of the internal pressure on the equivalent stress distribution in the tube, an experimental study is done by constructing a testing rig to apply the hydraulic pressure and three dies are manufactured with different bulging configurations (square, cosine, and conical). In the other part, ANSYS APDL is generated to analyze the bulging process with hydraulic and rubber (natural and industrial) media. It was found that when the media is a rubber, the stress is decreased about 9.068% in case of cosine die and 5.4439% in case of conical die and 2.8544% in case of square die. So, it can be concluded that the internal pressure in the rubber media is much better than in hydraulic media. Also, the force needed for fo
... Show More
Marriage is a holly secret in Christian religion .So it id natural that its ceremonies acquired religious form .In general the marriage is contracted by minister of religion in presence of the two parties or by a proxy or presence of parents if it is necessary . And to make the condition of publicity for the marriage ,its procedures must be made before witnesses .Also the minister of religionhave to confirm the agreement of the two parties before beginning the procedures.The marriage ceremonies are made.These procedures are religious traditions that includes praying and make blessings and putting the rings in fingers by thepriest . The marriage is a holly secret performed by the crown pray according to the church religious traditions
Christianity has rituals and rituals to be carried out, and can not be abandoned, and they see that the sacred statutes ordered by Christ () his followers, including: (the mystery of baptism between Christian denominations, descriptive study) A Christian is to be baptized as the seal of faith, as evidenced by the Bible in the words of Jesus to His disciples.
Baptism takes place in the name of the Father, the Son, and the Holy Spirit. This makes them Christian through the practice of this obligatory man enters the Church, represented by the death, burial, and resurrection of Christ according to their belief. And every person who has received the sacrament of baptism remains a Christian until death, in the light of what they see.
The present study aims at analyzing the polysemy of the English preposition in from the cognitive linguistic (CL) point of view using Evans' and Tyler's approach (2003). The perplexity faced by Iraqi second language learners (L2) due to the multi-usages of this preposition has motivated the researcher to conduct this study. Seventy-six second year university students participated in this experimental study. The data of the pre-test and post-test were analyzed by SPSS statistical editor. The results have shown the following: First, a progress of more than (0.05≤) has been detected as far as students' understanding of the multiple usages of the preposition in is concerned. Second, the results of the questionnaire have s
... Show MorePraise be to God, Lord of the worlds, and prayers and peace be upon our master Muhammad and his family and companions until the Day of Judgment.
The words of God Almighty are for the sake of the greatest and greatest speech, and the scholars, may God have mercy on them, raced.
To dive into knowing the word of God and what he intended, so they wrote in it the literature and collected works in it, and explained it to those after them.
And when the noble companions, were extremely eloquent and eloquent, because the Holy Qur’an was revealed in the language of the Quraysh, and all the Arabs knew their language, they understood the Holy Qur’an and applied it p
النظام السياسي اليمني : دراسة في المتغيرات الداخلية
Background: One of the drawbacks of vital teeth bleaching is color stability. The aim of the present study was to evaluate the effects of tea and tomato sauce on the color stability of bleached enamel in association with the application of MI Paste Plus (CPP-ACPF). Materials and Methods: Sixty enamel samples were bleached with 10% carbamide peroxide for two weeks then divided into three groups (A, B and C) of 20 samples each. After bleaching, the samples of each group were subdivided into two subgroups (n=10). While subgroups A1, B1 and C1 were kept in distilled water, A2, B2, and C2 were treated with MI Paste Plus. Then, the samples were immersed in different solutions as follow: A1 and A2 in distilled water (control); B1 and B2 in black
... Show More