Multipoint forming process is an engineering concept which means that the working surface of the punch and die is produced as hemispherical ends of individual active elements (called pins), where each pin can be independently, vertically displaced using a geometrically reconfigurable die. Several different products can be made without changing tools saved precious production time. Also, the manufacturing of very expensive rigid dies is reduced, and a lot of expenses are saved. But the most important aspects of using such types of equipment are the flexibility of the tooling. This paper presents an experimental investigation of the effect of three main parameters which are blank holder, rubber thickness and forming speed th

 A problem of solid waste became in the present day common global problem among all countries, whether developing or developed countries, and can say that no country in the world today is immuning from this dilemma which must find appropriate solutions. The problem has reached a stage that can not ignore or delay, but has became a daily problem occupies the minds of ecologists, economists and politicians took occupies center front in the lists of  priorities for the countries in terms of finding solutions to the rapid scientific and radical them. and that transport costs constitute an important component of total costs borne by the municipal districts in the process of disposal of solid waste, so any improvement in the

The present study is to investigate the possibility of using wastes in the form of scrap iron (ZVI) and/ or aluminum ZVAI for the detention and immobilization of the chromium ions in simulated wastewater. Different batch equilibrium parameters such as contact time (0-250) min, sorbent dose (2-8 g ZVI/100 mL and 0.2-1 g ZVAI/100 mL), initial pH (3-6), initial pollutant concentration of 50 mg/L, and speed of agitation (0-250) rpm were investigated. Maximum contaminant removal efficiency corresponding to (96 %) at 250 min contact time, 1g ZVAI/ 6g ZVI sorbent mass ratio, pH 5.5, pollutant concentration of 50 mg/L initially, and 250 rpm agitation speed were obtained.

The best isotherm model for the batch single Cr(III) uptake by ZVI

    Heat exchanger is an important device in the industry for cooling or heating process. To increase the efficiency of heat exchanger, nanofluids are used to enhance the convective heat . transfer relative to the base fluid. - Al2O3/water nanofluid is used as cold stream in the shell and double concentric tube heat exchanger counter current to the hot stream basis oil. These nanoparticles were of particle size of 40 nm and it was mixed with a base fluid (water) at volume
concentrations of 0.002% and 0.004%. The results showed that each of Nusselt number and overall heat transfer coefficient increased as nanofluid concentrations increased. The pressure drop of nanofluid increased slightly than the base fluid because

The picture has taken a place that sometimes enables it to take precedence over media analysis، psychology، and political communication.
The image has the ability to influence to obtain persuasion، not only emotionally or
dramatically، but also on the level of commercial and political persuasion. In every
image، the intention of that persuasion is hidden.
It can be identified by a set of underlying dimensions such as vitality، social dominance، and confidence، for which a group of specific suggestions or movements، such
as a smile، the movement of hands، or the nature and way of looking with the eyes، is
established. The visual image often precedes its verbal counterpart in the proce

المستخلص: يهدف البحث الى التعرف على بقاء اثر المعلومة عن طريق الاجابة عن السؤال: ما مدى بقاء اثر التعلم بين التعليم الالكتروني والتعليم االحضوري ؟ تم تطبيق البحث في العام الدراسي( 2020-2021 م) في العراق. تم استخدام المنهج الوصفي بالاسلوب المقارن في عقد مقارنة بين التعليم الالكتروني والتعليم الحضوري. وكان مجتمع البحث من طلبة المرحلة الرابعة كلية التربية للعلوم الصرفة – ابن الهيثم ,و العيتة من قسم الرياضيات الم

Prince Kikaus  explained  to us Conditions of writing and establishing .Then he touched  upon the Conditions of the ministry and qualities that must be characterized Author and minister both need machines must be availabla in person if given these positions .he was creative in presenting his ideas which is not  without judgment an knowledge.He had a distinct style in mentioned professions and administrative hierarchy As explained in his speech About the writer and his Correspondence and construction and writer position who has developed into a minister then he touched it to the cabinet system and what the minister should do.of qualities .and the importance of the post of minister who mentioned several points to him ou