This paper presents an application of a Higher Order Shear Deformation Theory (HOST 12) to problem
of free vibration of simply supported symmetric and antisymmetric angle-ply composite laminated plates.
The theoretical model HOST12 presented incorporates laminate deformations which account for the effects
of transverse shear deformation, transverse normal strain/stress and a nonlinear variation of in-plane
displacements with respect to the thickness coordinate – thus modeling the warping of transverse crosssections more accurately and eliminating the need for shear correction coefficients. Solutions are obtained in
closed-form using Navier’s technique by solving the eigenvalue equation. Plates with varying number of

Seventy five adult virgin female Norway rats (60 experimental and 15 controls) were used to evaluate the effect of seeds of three herbs (Fennel, Cumin and Garden cress) on their mammary glands. Experimental animals were fed with these herbs (each type of herb seeds was given to twenty experimental rats) for fourteen days. Rats were sacrificed and mammary gland sections were obtained, stained then morphometrically assessed. Serum prolactin level was performed too. Results revealed that Garden cress seeds are the strongest lactogenic agent among the three. Both Fennel and Cumin seeds were shown to be very weak galactagogues.

Hepatitis, an inflammation of the liver, has a number of infectious and non-infectious causes. Two of the viruses that cause hepatitis (hepatitis A and E) can be transmitted through water and food; hygiene is therefore important in their control. First, to assess the importance of HAV and HEV as a possible diagnosis for clinically diagnosed patients with acute viral hepatitis. Second, to assess the prevalence of hepatitis A and E in all provinces of Iraq and study its association with age, gender. This study consisted of two groups: The first group consisted of 2975 patients with a clinical diagnosis of acute viral hepatitis. The second group consisted of a total of 9610 persons, which were recruited by surveying a nationally representative

Buckling analysis of composite laminates for critical thermal (uniform and linear) and mechanical loads is reported here. The objective of this work is to carry out theoretical investigation of buckling analysis of composite plates under thermomechanical loads, and experimental investigation under mechanical loads. The analytical investigation involved certain mathematical preliminaries, a study of equations of orthotropic elasticity for classical laminated plate theory (CLPT), higher order shear deformation plate theory (HSDT) , and numerical analysis (Finite element method), then the equation of motion are derived and solved using Navier method and Levy method for symmetric and anti-symmetric cross-ply and angle-ply laminated plates t

The present work covers the Face-Hobbing method for generation and simulation of meshing of Face hobbed hypoid gear drive. In this work the generation process of hobbed hypoid gear has been achieved by determination of the generation function of blade cutter. The teeth surfaces have been drawn depending on the simulation of the cutting process and the head cutter motion. Tooth contact analysis (TCA) of such gear drive is presented to evaluate analytically the transmission error function for concave and convex tooth side due to misalignment errors. TCA results show that the gear is very sensitive to misalignment errors and
the increasing of the gear teeth number decrease the transmission error for both concave and convex tooth sides a

The National Charter for Education and Training in 1999 defined the principles, pillars and main objectives of the Moroccan education system, building on the various reforms of the early twenty-first century and the attempt to breathe new life into this reference document. Through partial and incremental changes, a total inability to tackle the root causes of the Moroccan education system and training has been revealed. This research has been conducted to answer the questions of education in the foreground national concerns and priorities in the discourse of the main political actors in Morocco that have been raised and remain interesting and can be expressed in the following question: Morocco still fails to meet the challenge of educati

There are many different methods for analysis of two-way reinforced concrete slabs. The most efficient methods depend on using certain factors given in different codes of reinforced concrete design. The other ways of analysis of two-way slabs are the direct design method and the equivalent frame method. But these methods usually need a long time for analysis of the slabs.

In this paper, a new simple method has been developed to analyze the two-way slabs by using simple empirical formulae, and the results of final analysis of some examples have been compared with other different methods given in different codes of practice.

The comparison proof that this simple proposed method gives good results and it can be used in analy

Tafsir, ‘interpretation’ is one of the most important sciences the Muslims need. Because Allah, Almighty, revealed the Qur’an to be a way of life for the Muslims in which the healing of what is in the chest, including their goodness and their peasant. Allah says:
“O people, an admonition has indeed come to you from your Lord and a healing for what is in the hearts; and a guidance and a mercy for the believers.”
In order to achieve the goal for which God revealed the Quran must be understood and managed verses:” This is a Book that We have revealed to you abounding in good, that they may ponder over its verses, and that those who have understanding may be mindful.”
The Prophet (PBUH) and his companions understood t

A cantilever beam is made from composite material which is consist of (matrix: polyester) and (particles: Silicon-Carbide) with different volume fraction of particles. A force is applied at the free end of beam with different values. The experimental maximum deflection of beam which occurs at the point of the applied load is recorded. The deflection and slope of beam are analyzed by using FEM modeling. MATLAB paltform is built to assemble the equations, vector and matrix of FEM and solving the unknown variables (deflection and slope) at each node. Also ANSYS platform is used to modeling beam in finite element and solve the problem. The numerical methods are used to compare the results with the theoretical and experimental data. A good ag