Experimental investigations had been done in this research to demonstrate the effect of carbon fiber and Ceramic fillers contents on the tribological behaviour of (15% volume fraction) carbon-epoxy composite system under varying volume fraction, load, time and sliding distance. The wear resistance were investigated according to ASTM G99-05standard using pin on disc machine to present the composite tribological behaviour. The influence of three ceramic fillers, granite, perlite and calcium carbonate (CaCO3), on the wear of the carbon fabric reinforced epoxy composites under dry sliding conditions has been investigated. The effect of variants in volume fraction, applied load, time and sliding distance on the wear behaviour of polymer composites is studied by measuring the weight changes . In the experiments with wear test pin having flat face in contact with hardening rotating steel disc, sliding speed, time and loads in the range of 200 RPM, 300–900s and 40–60 N respectively was used. It is observed that the wear resistance increase with the increasing of reinforcement material volume fraction while, the wear rate increases with increasing of applied load, time and sliding distance. The results showed that the filler of granite perlite and CaCO3 as filler materials in carbon epoxy composites will increase the wear resistance of the composite greatly than carbon fiber fillers epoxy composite only and granite filled CE Composite exhibited the maximum wear resistance.
The structural, optical and photoelectrical properties of fabricated diffusion heterojunction (HJ) solar cell, from n-type c-Si wafer of [400] direction with Boron, has been studied. AgAl alloys was used because of its properties that affect as a good connection materials. TiO2 has been used as a reflecting layer to increase the absorption radiation. The HJ has direct allowed energy gap equal to 3.1 eV. The c-Si/B HJ solar cell yielded has an active area conversion efficiency of 16.4% with an open circuit voltage of (Voc) 0.592V, short circuit current (Isc) of 2.042mA, fill factor (F.F) of 0.682 and % =10.54.
Equilibrium Moisture sorption isotherms are very important in drying and storage analysis. Experimental moisture equilibrium data (adsorption and desorption) of Aspirin were determined using the static method of saturated salt solutions and that by exposing the material to different conditions of temperatures and water activities. Three different temperatures (25, 30, 40Cº) and water activities in the range of (6.3- 83.6%) were used. The results showed that the equilibrium moisture content increased with the increase in water activity at any temperature and decreased with temperature increase at constant water activity. The water activity increases with increasing in temperature when moisture content was kept constant. The sorption isot
... Show MoreIn this paper, the concept of a neutrosophic KU-algebra is introduced and some related properties are investigated. Also, neutrosophic KU-ideals of a neutrosophic KU-algebra are studied and a few properties are obtained. Furthermore, a few results of neutrosophic KU-ideals of a neutrosophic KU-algebra under homomorphism are discussed
The bony pelvis has a major role in weight transmission to the lower limbs. The complexities of its geometric form, material properties, and loading conditions render it an open subject to biomechanical analysis.
The present study deals with area measurement, and three-dimensional finite element analysis of the hip bone to investigate magnitudes, load direction, and stress distribution under physiological loading conditions.
The surface areas of the auricular surface, lunate surface, and symphysis pubis were measured in (35) adult hip bones. A solid model was translated into ANSYS parametric design language to be analyzed by finite element analysis method under different loading conditions.
The surface
... Show MoreLignans are natural products widely distributed in the plant kingdom. They are composed of two β-β-linked phenylpropane (shikimate-derived biogenetic subunits). Although the backbone of lignans is composed of phenylpropane units, there is enormous diversity in the structure of lignans leading to different classes of lignans, such as γ-butyrolactone derivatives, eg. Hymatairesinol, bicyclooctadiene derivatives, e.g. pinoresinol, tetrahydrofuran derivatives e.g.lariciresinol, di-arylbutandiol derivatives, e.g. secoisolariciresinol. Introduction of a further carbon –carbon linkage leads to a class of lignans collectively known as cyclolignans such as tetrahydro-naphthalene derivatives, for example podophyllotoxin. Lignans ha
... Show MoreThe aim of this study is to formulate and evaluate ezetimibe nanoparticles using solvent antisolvent technology. Ezetimibe is a practically water-insoluble drug which acts as a lipid lowering drug that selectively inhibits the intestinal absorption of cholesterol and related phytosterols. Ezetimibe prepared as nano particles in order to improve its solubility and dissolution rate.
Thirty formulas were prepared and different stabilizing agents were used with different concentrations such as poly vinyl pyrrolidone (PVPK-30), poly vinyl alcohol (PVA), hydroxy propyl methyl cellulose E5 (HPMC), and poloxamer. The ratios of drug to stabilizers used to prepare the nanoparticles were 1: 2, 1:3 and 1:4.
The prepared nanoparticles
... Show MoreThis paper exclusively deals with medical encounters. . Structurally and thematically, it manifests itself in five parts. The First part deals with medical encounters as well as essential speech activities which cover (a) frames (certain types of talk) (b) the patient’s account and the patient’s story or more precisely the patient telling his story and (c) the act of questioning the patient. The Second part revolves round genre and register. The former, in most cases, suggests that the format of medical encounters is conversational. With register; we have a converse reality that restrictively tries to narrow things and give them a certain flavor. The Third part realizes the technicalities of medical encounters (a) the setting of an inte
... Show More