Direct field-orientation Control (DFOC) of induction motor drives without mechanical speed sensors at the motor shaft has the attractions of low cost and high reliability. To replace the sensor, information on the rotor speed and position are extracted from measured stator currents and from voltages at motor terminals. In this paper presents direct field-orientation control (DFOC) with two type of kalman filter (complete order and reduced order extended kalman filter) to estimate flux, speed, torque and position. Simulated results show how good performance for reduced order extended kalman filter over that of complete order extended kalman filter in tracking performance and reduced time of state estimation.
<span lang="EN-US">We are living in the 21<sup>st</sup> century, an era of acquiring necessity in one click. As we, all know that technology is continuously reviving to stay ahead of advancements taking place in this world of making things easier for mankind. Technology has been putting his part in introducing different projects as we have used the field programmable gate arrays (FPGAs) development board of low cost and programmable logic done by the new evolvable cyclone software is optimized for specific energy based on Altera Cyclone II (EP2C5T144) through which we can control the speed of any electronic device or any Motor Control IP product targeted for the fan and pump. Altera Cyclone FPGAs’ is a board thro
... Show MoreThis study, establishes two stochastic monotonicity results concerning the run length of an upper one –sided Exponentially Weighted Moving Average (EWMA) control charts, based on the logarithm of the sample variance, for monitoring a process standard deviation, these properties cast interesting light on the control chart performance, and their extension to other one –sided EWMA control charts.
In this work, laboratory experiments were carried out to verify direct contact membrane distillation system’s performance in highly saline water desalination. The study included the investigation of various operating conditions, like feed flow rate, temperature and concentration of NaCl solution and their impact on the permeation flux were discussed. 16 cm2 of a flat sheet membrane module with commercial poly-tetra-fluoroethylene (PTFE) membrane, which has 0.22 μm pore size, 96 µm thickness and 78% average porosity, was used. A high salt rejection factor was obtained greater than 99.9%, and the permeation flux up to 17.27 kg/m2.h was achieved at 65°C for hot feed side and 20°C for cold side stream.
The purpose of research is highlighting the role of tax expenses in promoting direct foreign investment in Iraq, The main objective of the increase in the field of tax expenses is to manage the competition in the production of goods and services locally, in addition to the various qualities of the economical. As the search contributes to the idea of the role of the policy of the tax expenses in the promotion of foreign companies operating in Iraq. The analytical and transparent transparency used by adoption of cases of the relevant body of the tax body. For each image or form of tax expenses have been reliably related to the promotion of direct foreign investment, the taxpayers highlighted the annual controls, tax cuts as the sample was
... Show MoreForeign direct investment is considered one of important bases to blind economy for many. Countries as if the main stage for developing national economy ,so for this ,many of countries give great prominence to the role of drivel foreign investment due to its importance as one of economic growth pillars in the developing countries. They offer a support for modern technology, organizational and managerial skills.
Dneto the importance of direct foreign investment on the economic growth, today, we discover that Iraq in need to rebnlid the in frastructuve and renew what has been destroyed during was in many production and export institutions . as wel
... Show More:
While practicing of International business particularly that centered on foreign direct investment, let on one side, to achieving objectives of transnational corporations specially that represented in continuous pursue to improving its cash flows and maximization of stockholders wealth which is considered the most important objective to the transnational corporations, but in the same time its lead, on other side, to increasing the foreign exchange risk exposuring these corporations. So, the transnational corporations (TNCs) struggling to make strategies which are dealing in smart way, with this risk and its management in way that enable to avoiding risk comple
... Show MoreDeveloping countries have depended since long time on the developed countries to increase the levels of development and improving rates of growth direction to the best way where taking this dependence many shapes influenced by the evolution form of international relations and this dependence shows how the great deficiencies in sources of local financing, which called developing countries to increase their reliance on external funding sources, represented in the form of grants, subsidies, loans and foreign investment, pursuing States in that the application of economic reform policies in pursuit of faster economic growth and restructure its economy and achieve economic stability. In the early eighties of the last
... Show MoreCurrently, there is an intensive development of bipedal walking robots. The most known solutions are based on the use of the principles of human gait created in nature during evolution. Modernbipedal robots are also based on the locomotion manners of birds. This review presents the current state of the art of bipedal walking robots based on natural bipedal movements (human and bird) as well as on innovative synthetic solutions. Firstly, an overview of the scientific analysis of human gait is provided as a basis for the design of bipedal robots. The full human gait cycle that consists of two main phases is analysed and the attention is paid to the problem of balance and stability, especially in the single support phase when the biped
... Show MoreThis paper presents an investigation to the effect of the forming speed on healing voids that inhabit at various size in an ingot. The study was performed by using finite element method with bilinear isotropic material option, circular type voids were considered. The closure index was able to predict the minimum press force necessary to consolidate voids and the reduction. The simulation was carried out, on circular cross-section lead specials containing a central void of different size. At a time with a flat die, different ratio of inside to outside radius was taken with different speed to find the best result of void closure.