يهدف البحث الحالي إلى اختبار العلاقة بين نوعية حياة العمل والإبداع التنظيمي في ديوان وزارة التخطيط ، ولبلوغ الهدف المذكور وبناء على معطيات البحث الاستطلاعي للباحث بني ألانموذج الفرضي للبحث الذي ضم المتغير المستقل والمعتمد، واعتماداً على حركية الأنموذج صيغت فرضيتان، ولاختبار صحة الفرضيات وجمع المعلومات من عينة البحث البالغة (100) مدير يمثلون مرك

Abstract 

In the present study, composites were prepared by Hand lay-up molding. The composites constituents were epoxy resin as a matrix, 6% volume fractions of glass fibers (G.F) as reinforcement and 3%, 6% volume fractions of preparation natural material (Rice Husk Ash, Carrot Powder, and Sawdust) as filler. Studied the erosion wear behavior and coating by natural wastes (Rice Husk Ash) with epoxy resin after erosion. The results showed the non – reinforced epoxy have lower resistance erosion than natural based material composites and the specimen (Epoxy+6%glass fiber+6%RHA) has higher resistance erosion than composites reinforced with carrot powder and sawdust  at 30cm , angle 60

In this paper, a new third kind Chebyshev wavelets operational matrix of derivative is presented, then the operational matrix of derivative is applied for solving optimal control problems using, third kind Chebyshev wavelets expansions. The proposed method consists of reducing the linear system of optimal control problem into a system of algebraic equations, by expanding the state variables, as a series in terms of third kind Chebyshev wavelets with unknown coefficients. Example to illustrate the effectiveness of the method has been presented.

Self- curing is the potential of lightweight aggregate to absorption great amount of water thru mixing which prominently can moves to the paste during hydration process. Self- curing empowers a water to be distributes more evenly act out the cross section. Whereas, the external curing water is only able to penetrate several millimetres into concrete with low water cement ratio. Brick dust accumulates in the demolish site creates serious environmental contamination. This study investigates the effect of brick dust recovered from construction site on the Properties of mortar cured in three curing conditions. Mortar in this study produced using BD as cement additive with (2, 4, 6, and 8) % by weight of cement. BD was used a

In this study, a 3 mm thickness 7075-T6 aluminium alloy sheet was used in the friction stir welding process. Using the design of experiment to reduce the number of experiments and to obtain the optimum friction stir welding parameters by utilizing Taguchi technique based on the ultimate tensile test results. Orthogonal array of L9 (3³) was used based on three numbers of the parameters and three levels for each parameter, where shoulder-workpiece interference depth (0.20, 0.25, and 0.3) mm, pin geometry (cylindrical thread flat end, cylindrical thread with 3 flat round end, cylindrical thread round end), and thread pitch (0.8, 1, and 1.2) mm) this technique executed by Minitab 17 software. The results showed th

Phytoplankton, as one of the most important primary producers in aquatic ecosystems, has been widely used to indicate the health of ecosystems. Nine physico-chemical parameters of water, as well as the phytoplankton community, of Al-Chibayish marsh were studied. Samples were collected from four sites and analyzed every two months from January to October 2019.

    Seasonal variations in physical and chemical properties were observed at all sites during the study period. The results indicated that 154 species of phytoplankton were recorded. The highest percentage of species was recorded to be 64.28% for Bacillariophyceae (diatoms) (Centrales 3.24% and Pennales 61.03%), followed by Chlorophyceae (16.23%), Cyanophyceae

     Atenolol was used with ammonium molybdate to prove the efficiency, reliability and repeatability of the long distance chasing photometer (NAG-ADF-300-2) using continuous flow injection analysis. The method is based on reaction between atenolol and ammonium molybdate in an aqueous medium to obtain a dark brown precipitate. Optimum parameters was studied to increase the sensitivity for developed method. A linear range for calibration graph was 0.1-3.5 mmol/L for cell A and 0.3-3.5 mmol/L for cell B, and LOD 133.1680 ng/100 µL and 532.6720 ng/100 µL for cell A and cell B respectively with correlation coefficient (r) 0.9910 for cell A and 0.9901 for cell B, RSD% was lower than 1%, (n=8) for the determination of ate

In the process of translating Qur’anic texts, there is an urgent need for interpretations of the Qur’anic text due to the presence of many incomprehensible Qur’anic verses or words because of our distance from the standard Arabic, language in which the Holy Qur’an was revealed, and the introduction of the foreign words into our language, in addition to the fact that many Qur’anic words are no longer used. All this prompted the need for the interpretation of the Qur'anic text, Therefore, it is necessary for the translator to resort to the books of interpretation if he intends to translate the Qur’an

This research deals with the rhetoric purposes of the passive voice in the holy Quran. First, we put an introductory to the concept of the Quran language and its difference of the spoken Arabic language during the revelation period. Besides; we gave a brief about the structure passive voice form of Arabic language. Second, we explained the purposes of passive voice used in the holly Quran with sufficient examples, commentaries and clarifications about all the cases. Rhetoric purposes that we deals with are: concision, emphasize an idea, avoid using the subject because it is known and clear for all or because it is really unknown, etc. This part has contained the most important purposes for the use of passive voice in holy Quran. At the end