أن الفن الإسلامي المبكر تضمن أمثلة عديدة لرسوم جداريه آدمية وحيوانية ونباتية وهندسية بشكل متفرد ومتميز، وجد في القصور القديمة ، و بوجه عام في العصور المبكرة ، على الرغم من موقف الدين الإسلامي من الرسوم .
اذ ان موقفه من تصوير الكائنات الحية ايجابيا على الرغم من محاولات بعض المختصين وعلى رأسهم الأب لاما نس Henri Lammens وماسينون Louis Massignon وكرسويل K.A.C Creswell أن يبرهنوا على أن الدين الإسلامي لم يعترض على التصوير وصناعة

This article conclude a theoretical study for the possibility to produce additional electric power from Iraqi steam power plants by  cutting – off high-pressure feed water heaters .  Three separated steam power plants which Dura , south –Baghdad and Nasria were studied . The investigation showed the possibity of increasing the electric power from 10 to 15% for Dura and Nasria , whereas 6% for south – Baghdad . According to the nowadays of operation to Iraqi steam power plants , the results showed that by cutting–off high  pressure feed water heaters we can generate additional electric power about 250 MW during 3-4 hrs. daily. In addition, the fuel consumption can be reduced in comparison with diesel generat

   This research includes the application of non-parametric methods in estimating the conditional survival function represented in a method (Turnbull) and (Generalization Turnbull's) using data for Interval censored of breast cancer and two types of treatment, Chemotherapy and radiation therapy and age is continuous variable, The algorithm of estimators was applied through using (MATLAB) and then the use average Mean Square Error (MSE) as amusement  to the estimates and the results showed (generalization of Turnbull's) In estimating the conditional survival function and for both treatments ,The estimated survival of the patients does not show very large differences

This paper is focused on studying the effect of cutting parameters (spindle speed, feed and depth of cut) on the response (temperature and tool life) during turning process. The inserts used in this study are carbide inserts coated with TiAlN (Titanum, Aluminium and Nitride) for machining a shaft of stainless steel 316L. Finite difference method was used to find the temperature distribution. The experimental results were done using infrared camera while the simulation process was performed using Matlab software package. The results showed that the  maximum difference between the experimental and simulation results was equal to 19.3 , so, a good agreement between the experimental and simulation results  was achieved. Tool life w

The fouling depositions of crude oil stream were studied theoretically in a shell and tube heat exchanger to investigate the effect of depositions on the heat transfer process. The employed heat exchanger was with steam flowing in the inner tubes and crude oil in the shell at different velocities and bulk temperatures. It is assumed that fouling occurs only on the heated stream side (crude oil). The analysis was carried out for turbulent flow heat transfer conditions with wide range of Reynolds number, bulk temperature and time. Many previously proposed models for fouling resistance were employed to estimate a new model for fouling rate. It is found that the fouling rate and consequently the heat transfer coefficient were affected by Rey

The sol-gel preparation technique of transparent silica monoliths containing up to 0.5 M of samarium have been described. The sol-gel processing parameters are: acid catalyzed hydrolysis and controlled drying. The prepared monoliths are analyzed by X-ray diffraction, pycnometer measurements, Fourier transformation infrared spectroscopy and optical spectroscopy. The oscillator strengths of the Sm3+ ions in the silica monoliths are calculated. The results show a linear concentration dependence of some Sm3+ transitions in UV/Vis absorption spectra and formation of Sm3+ clusters inside the pores structure of silica monoliths at high Sm3+ concentration

This study was conducted to examine the anatomical aspects of Carissa macrocarpa, of stem, leaf and leaf venation. The results obtaind showed that the tissue of the studied parts have important anatomical characteristics in terms of the shape of the cross-sectional of stem and vertical-sectional of leaves. The stem section appeared in circular and the midrib was crescent shape and the stomata appeared on the upper surface of the leaf only, Tetracytic in type. Druses crystals and Aleurone granules appeared on both surfaces of leaves. The venation type was Brochidodromous in which the secondary veins do not end at the edge of the leaf, and each secondary race is connected with the higher rac