The forensic evidence important for the sources of legislation after the book of God Almighty and the Sunnah of the purified, including what is agreed upon in the protest, which is the book and the Sunnah and consensus, and what is different in the protest, such as measurement and approval and say companions and interests sent, and that the approval of the evidence that did not agree Accordingly, the terms of the fundamentalists differed and their definition differed with the similarity between each other, and the approval in some schools is an argument is not considered as the Shaafa'is, so it may correspond to measurement with them, but the approval at the tap and those who agree is a hidden measurement is likely to clear measurement,I

In this paper, the speed control of the real DC motor is experimentally investigated using nonlinear PID neural network controller. As a simple and fast tuning algorithm, two optimization techniques are used; trial and error method and particle swarm optimization PSO algorithm in order to tune the nonlinear PID neural controller's parameters and to find best speed response of the DC motor. To save time in the real system, a Matlab simulation package is used to carry out these algorithms to tune and find the best values of the nonlinear PID parameters. Then these parameters are used in the designed real time nonlinear PID controller system based on LabVIEW package. Simulation and experimental results are compared with each other and showe

In this research TiO2 nano-powder was prepared by a spray pyrolysis technique and then adds to the TiO2 powder with particle size (0.523 μm) in ratio (0, 5, 10, 15 at %) atomic percentage, and then deposition of the mixture on the stainless steel 316 L substrate in order to use in medical and industrial applications.
Structure properties including x-ray diffraction (XRD) and scanning electron microscope (SEM0, also some of mechanical properties and the effect of thermal annealing in different temperature have been studied. The results show that the particle size of a prepared nano-powder was 50 up to 75 nm from SEM, and the crystal structure of the powders (original and nano powder) was rutile with tetragonal cell. An improvement in

This paper aimed to investigate the effect of the height-to-length ratio of unreinforced masonry (URM) walls when loaded by a vertical load. The finite element (FE) method was implemented for modeling and analysis of URM wall. In this paper, ABAQUS, FE software with implicit solver was used to model and analysis URM walls subjected to a vertical load. In order to ensure the validity of Detailed Micro Model (DMM) in predicting the behavior of URM walls under vertical load, the results of the proposed model are compared with experimental results. Load-displacement relationship of the proposed numerical model is found of a good agreement with that of the published experimental results. Evidence shows that load-displacement curve obtained fro

Design and build a center basins new p-type four mirrors were studied its effect on all parameters evaluating the performance of the solar cell silicon in the absence of a cooling system is switched on and noted that the efficiency of the performance Hzzh cell increased from 11.94 to 21 without cooling either with cooling has increased the efficiency of the

A study of interactivity in the Iraqi newspaper sites_ An analytical study of the website of Al-Mada, Al-Zaman, Al-Sabah and Tariq Al-Shaab newspaper sought to determine the amount of interactivity in the sites of Iraqi newspapers that have been published since 2003, which consists of (15) newspapers according to the statistics of the Iraqi Books and Documents House.

and the researcher conducted an analytical survey on these sites, and the percentage of interactivity in general was weak, not more than (47.1%), and this weakness in interactivity contributed greatly to the decline in surfers of the websites of those electronic newspapers.

The highest aggregate rate of the research sample was in the simple interactive tools

Objective: To evaluate and compare the effect of mechanical surface treatment (groove, aluminum oxide particles)
with 45 degree bevel type of joint on tensile bond strength of acrylic specimens repaired by two curing methods
(microwave and water both).
Methodology: Eighty specimens (80) were prepared from pink heat cure acrylic resin. They were divided into two
main groups (40 specimen repaired by microwave energy and 40 specimens repaired by water bath method).Each
group can be divided into four subgroups of ten according to the surface treatment. The control group A was left
intact, group B received no surface treatment, group C and D received surface treatment by (groove, 50 m aluminum
oxide particles). Specimens