Under cyclic loading, aluminum alloys exhibit less fatigue life than steel alloys of similar strength and this is considered as Achilles's heel of such alloys. A nanosecond fiber laser was used to apply high speed laser shock peening process on thin aluminum plates in order to enhance the fatigue life by introducing compressive residual stresses. The effect of three working parameters namely the pulse repetition rate (PRR), spot size (ω) and scanning speed (v) on limiting the fatigue failure was investigated. The optimum results, represented by the longer fatigue life, were at PRR of 22.5 kHz, ω of 0.04 mm and at both v's of 200 and 500 mm/sec. The research yielded significant results represented by a maximum percentage increase in the fatigue life of 505.25% accompanied by the least deformation for the processed surfaces. SEM images for the specimens processed by the optimum process conditions imply no ablation has occurred at the surface, and the process is completely cold. X-ray diffraction analysis indicates a reduction in grains size, an increase of 28.56% in the lengths of dislocations and formation of effective compressive residual stress at the surface and beneath reaches to 700 μm.
Thermal pyrolysis kinetics of virgin high-density polyethylene (HDPE) was investigated. Thermal pyrolysis of HDPE was performed using a thermogravimetric analyzer in nitrogen atmosphere under non-isothermal conditions at different heating rates 4, 7, 10 °C/min. First-order decomposition reaction was assumed, and for the kinetic analysis Kissinger-Akahira-Sunose(KAS), Flynn-Wall-Ozawa(FWO) and Coats and Redfern(CR) method were used. The obtained values of average activation energy by the KAS and FWO methods were equal to137.43 and 141.52 kJ/mol respectively, these values were considered in good agreement, where the average activation energy value obtained by CR equation methods was slightly different which equal to 153.16 kJ/
... Show MoreOrganic permeable‐base transistors (OPBTs) show potential for high‐speed, flexible electronics. Scaling laws of OPBTs are discussed and it is shown that OPBT performance can be increased by reducing their effective device area. Comparing the performance of optimized OPBTs with state‐of‐the‐art organic field‐effect transistors (OFETs), it is shown that OPBTs have a higher potential for an increased transit frequency. Not only do OPBTs reach higher transconductance values without the need for sophisticated structuring techniques, but they are also less sensitive to parasitic contact resistances. With the help of a 2D numerical model, the reduced contact resistances of OPBTs are explained by a homogeneous injection of current acros
... Show MoreThe research aims to highlight on the reasons of financial & managerial corruption phenomena and to suggest systems & methods that promote controlling and developing the mechanism to combat corruption it also highlights on the ways that should available to enable the three regulatory agencies to reduce this phenomenon. The research depends on the following hypothesis "the governance of state institutions and the application of electronic government with depending on a correct mechanism to crossing auditing and the equilibrium performance model well help to reduce corruption phenomenon in Iraq" the two researchers have been concluded some conclusions the main one is that so many reasons of corruption starting from the bad
... Show MoreThis research is based on the study of common praise in Mutanabbi and Ibn Hani Al-Andalusi as the main purpose in poetry poets, and balance between them;
The research was divided into two topics, presented by introductory introduction for the purpose of praise, and the concept of budget in Arab criticism, and then presented a brief overview of the lives of poets.
In the first section, I dealt with the common objectivity of the poets, such as the subject of sincerity in praise, hyperbole in the person of Mamdouh, and self-esteem when asked, in addition to the most common characteristics in t
... Show MoreAbstract: Background: High percentage of diabetes patients complain from post extraction hemorrhage. Many types of hemostatic materials are used to stop bleeding after teeth extraction: diode lasers are good hemostatic agents owing to their highly absorption by hemoglobin therefore they are used in soft tissue procedures with relatively no effects on dental hard tissues due to their poorly absorption by water and hydroxyapatite. Objectives: The aim of this study is to evaluate the efficiency of diode laser to assist the clot formation after tooth extraction for type II diabetes patients with minimum temperature elevation to prevent periodontal destruction. Materials and methods: From 12 type II diabetes patients (7 males and 5 females wi
... Show MoreDo’a and Zikr al-Mā’thur (authentic supplications and remembrance of ALLAH ‘Azza wa Jalla) can be suggested to Muslims to help them deal with challenges or issues in life. Counselling cases affect a person’s feelings. Do’a and Zikr al-Mā’thur are often applied as a counselling intervention. Unfortunately, the authentic Do’a and Zikr al-Mā’thur are dispersed in many resources not visible to users, and the fact that not all online resources offer access to accurate Do’a and Zikr al-Mā’thur to users and the dubious Do’a and Zikr al-Mā’thur frequently credited to the Prophet (pbuh). The goal of this research is to develop an ontology
... Show MoreShatt Al-Hilla was considered one of the important branches of Euphrates River that supplies irrigation water to millions of dunams of planted areas. It is important to control the velocity and water level along the river to maintain the required level for easily diverting water to the branches located along the river. So, in this research, a numerical model was developed to simulate the gradually varied unsteady flow in Shatt AL-Hilla. The present study aims to solve the continuity and momentum (Saint-Venant) equations numerically to predict the hydraulic characteristics in the river using Galerkin finite element method. A computer program was designed and built using the programming language FORTRAN-77. Fifty kilometers was consid
... Show More