The prediction of the blood flow through an axisymmetric arterial stenosis is one of the most important aspects to be considered during the Atherosclrosis. Since the blood is specified as a non-Newtonian flow, therefore the effect of fluid types and effect of rheological properties of non-Newtonian fluid on the degree of stenosis have been studied. The motion equations are written in vorticity-stream function formulation and solved numerically. A comparison is made between a Newtonian and non-Newtonian fluid for blood flow at different velocities, viscosity and Reynolds number were solved also. It is found that the properties of blood must be at a certain range to preventing atheroscirasis

This work describes the weathering effects (UV-Irradiation, and Rain) on the thermal conductivity of PS, PMMA, PS/PMMA blend for packaging application. The samples were prepared by cast method at different ratios (10, 30, 50, 70, and 90 %wt). It was seen that the thermal conductivity of PMMA (0.145 W/m.K), and for PS(0.095 W/m.K), which increases by PS ratio increase up to 50% PS/PMMA blend then decreased that was attributed to increase in miscibility of the blend involved. By UV-weathering, it was seen that thermal conductivity for PMMA increased with UV-weathering up to (30hr) then decreased, that was attributed to rigidity and defect formation, respectively. For 30%PS/PMMA, there results showed unsystematic decrease in thermal conduct

Background: Fluoropyrimidines are widely used in the treatment of various solid tumors. One-third of cancer patients develop severe treatment-related toxicity. A part of fluoropyrimidine-related toxicity arises due to impaired activity of dihydropyrimidine dehydrogenase (DPD) caused by genetic variants in the DPYD gene. Objective: This study aims to determine the frequency of DPYD mutations among patients with adverse effects of 5-fluorouracil therapy. Materials and Methods: This cross-sectional study recruited 46 patients with 5-FU adverse effects. All demographic, clinical, and laboratory findings were recorded. Molecular testing was conducted to detect the DPYD mutation using the PGX-5FU StripAssay® kit, which identifies the IVS14 + 1G>

In this paper, a construction microwave induced plasma jet(MIPJ) system was used to produce a non-thermal plasma jet at atmospheric pressure, at standard frequency of 2.45 GHz and microwave power of 800 W. The working gas Argon (Ar) was supplied to flow through the torch with adjustable flow rate using flow meter regulator. The influence of the MIPJ parameters such as applied voltage and argon gas flow rate on macroscopic microwave plasma parameters were studied. The macroscopic parameters results show increasing of microwave plasma jet length with increasing of applied voltage, argon gas flow rate where the plasma jet length exceed 12 cm as maximum value. While the increasing of argon gas flow rate will cause increasing into the ar

This study was aimed to investigate the protective effect of vitamin D on L-arginine induced acute pancreatitis in rats. Twenty eight white Albino rats of both sexes were divided into 4 equal groups. Negative control rats (group I) intra-peritoneally injected with normal saline, positive control (group II) rats induced acute pancreatitis with L- arginine, group III rats treated with a single dose of vitamin D, and group IV treated with single dose of vitamin D prior to first dose of L- arginine. Serum amylase, lipase and cytokines such as tumour necrosis factor –alpha (TNF-α), interleukin-1 beta (IL1β); in addition, my eloperoxidase (MPO) enzyme activity in the pancreas were measured. In acute pancreatitis group (group II), there was a

Introduction: This study was performed to compare the effect of Fractional CO2 laser or Q switched Nd:YAG laser of surface treatment on the shear bond strength of zirconia-porcelain interface. Methods: Fractional CO2 laser at 30 W, 2 ms, time interval 1 ms, distance between spots 0.3 mm, and number of scans is (4) or Q switched Nd:YAG laser at 30 J/mm2 and 10 Hz were used to assess the shear bond strength of zirconia to porcelain. Pre-sintered zirconia specimens were divided into three groups (n = 10) according to the surface treatment technique used: (a) untreated (Control) group; (b) CO2 group; (c) Nd:YAG group. All samples were then sintered and veneered with porcelain according to the manufacturer’s instructions. Surface morph