The aerodynamic characteristics of the forward swept wing aircraft have been studied theoretically and experimentally. Low order panel method with the Dirichlet boundary condition have been used to solve the case of the steady, inviscid and compressible flow. Experimentally, a model was manufactured from wood to carry out the tests. The primary objective of the experimental work was the measurements of the wake dimensions and orientation, velocity defect along the wake and the wake thickness. A blower type low speed (open jet) wind tunnel was used in the experimental work. The mean velocity at the test section was (9.3 m/s) and the Reynolds number based on the mean aerodynamic chord and the mean velocity was (0.46x105). The measurements showed the existence of a three-dimensionality behavior in the wake flow field. Interference between the canard wake and the wing wake was observed. The canard effect on the wing root area was detected as the separation at the wing root was delayed due to the canard downwash. The aerodynamic coefficients for the forward swept wing aircraft were calculated using the measured wake shape from the experimental work. Numerical results showed that the canard extended the range of the angle of attack for the aircraft with a significant improvement for the lift curve slope compared to the aircraft without the canard.
Carbonate matrix stimulation technology has progressed tremendously in the last decade through creative laboratory research and novel fluid advancements. Still, existing methods for optimizing the stimulation of wells in vast carbonate reservoirs are inadequate. Consequently, oil and gas wells are stimulated routinely to expand production and maximize recovery. Matrix acidizing is extensively used because of its low cost and ability to restore the original productivity of damaged wells and provide additional production capacity. The Ahdeb oil field lacks studies in matrix acidizing; therefore, this work provided new information on limestone acidizing in the Mishrif reservoir. Moreover, several reports have been issued on the difficulties en
... Show MoreFriction stir spot welding (FSSW) is a relatively new welding process that may have significant advantages compared to the fusion processes as follows joining of conventionally non-fusion weldable alloys, reduced distortion and improved mechanical properties of weldable alloys joints due to the pure solidstate joining of metals. In this paper, a three-dimensional model based on finite element analysis is used to study the thermal history in the spot-welding of aluminum alloy 2024. The model take place the thermomechanical property on the process of the welded metals. The thermal history and the evolution results with numerical model at the measured point in the friction stirred spot weld have a good matching, then the prediction of the t
... Show More
Abstract
This research studies Abu Baker Al-Siddiq’s commandments to the leaders of his armies. The research is organized into an Introduction, three sections, and a Conclusion.
The Introduction presents a definition of Style and Commandment terminologies. It also presents a brief biography of Abu Baker Al-Siddiq may Allah be pleased with him.
The first section explains the characteristics of the Composition and its rhetorical significance. In this Section, I study the types of predicate and the methods of construction in Abu Baker’s commandments and the rhetoric in using the connection and disconnection modifiers in his expressions.
The second section e
... Show MoreLinking adverbials are used to organize and bridge together extended stretches of discourse to make the text coherent. They are explicit indicators of the communicative function of the sentence and writers use them to let their readers follow what has already been said and to help them anticipate what is about to follow.
Linking adverbials include those relations of addition, enumeration, summation, apposition and so on. Through the use of these adverbials, the writer is able to organize and develop his ideas and help the reader follow him from one sentence to another. Thus, a linking adverbial is a semantic relation used to show the way in which what is to follow is systematically connected to what has gone before. So, they have anap
In this work, the geomagnetic storms that occurred during solar cycles 23 and 24 were classified based on the value of the Disturbance Storm Time index (Dst), which was considered an indicator of the strength of geomagnetic conditions. The special criterion of Dst >-50 nT was adopted in the classification process of the geomagnetic storms based on the minimum daily value of the Dst-index. The number of geomagnetic storms that occurred during the study period was counted according to the adopted criteria, including moderate storms with (Dst >-50 nT), strong storms with (Dst >-100 nT), severe storms with (Dst >-200 nT), and great storms with (Dst >-350 nT). The statistica
The chemical bath deposition technique (CBD) is considered the cheapest and easiest compared with other deposition techniques. However, it is highly sensitive to effective parameter deposition values such as pH, temperature, and so on. The pH value of the reaction solution has a direct impact on both the nucleation and growth rate of the film. Consequently, this study presents a novel investigation into the effect of a precise change. in the pH reaction solution value on the structural, morphological, and photoresponse characteristics of tin monosulphide (SnS) films. The films were grown on a flexible polyester substrate with pH values of 7.1, 7.4, and 7.7. The X-ray diffraction patterns of the grown films at pH 7.1 and 7.4 confirmed
... Show MoreIn this research we solved numerically Boltzmann transport equation in order to calculate the transport parameters, such as, drift velocity, W, D/? (ratio of diffusion coefficient to the mobility) and momentum transfer collision frequency ?m, for purpose of determination of magnetic drift velocity WM and magnetic deflection coefficient ? for low energy electrons, that moves in the electric field E, crossed with magnetic field B, i.e; E×B, in the nitrogen, Argon, Helium and it's gases mixtures as a function of: E/N (ratio of electric field strength to the number density of gas), E/P300 (ratio of electric field strength to the gas pressure) and D/? which covered a different ranges for E/P300 at temperatures 300°k (Kelvin). The results show
... Show MoreThe research presented the tagged (aesthetic and expressive characteristics in the works of Jean Dubuffet), so the research objective was: to know the aesthetic and expressive characteristics in the works of (Jean Dubuffet), and the research included four chapters. The aim of the research, the limits of the research, and the definition of terms. The second chapter included four topics. The first topic presented the aesthetic essence and style, while the second topic dealt with expressionism: approaches in concept and meaning.
While the third topic was preoccupied with presenting the aesthetic and expressiveness in the drawings of modernity and beyond, while the fourth topic dealt with: Jean Dubuffet and the experience of raw art. Th
Twelve pends were selected and distributed on three verticals transects paths on the Tigers river in Al Rasheed county.Passing through land covers, that classified and covers the whole region. Based on the 8 Landsat of the year 2015. It was oriental classified by using Erdas 10.2 . The pedons were distributed on the area of each varicty of these classes. the series of soil according of the transect series (DW74,MMg,DMu6 , Df96) respectively were represented P1 , P2 , P3 , P4 .
The second transits series(DM97,MM5,DM96,DF115) respectively were represented P5 , P6 , P7 , P8 .The third transits series(DM46,MMg,MF12,MM11) re
... Show MoreIn this research, the electrical characteristics of glow discharge plasma were studied. Glow discharge plasma generated in a home-made DC magnetron sputtering system, and a DC-power supply of high voltage as input to the discharge electrodes were both utilized. The distance between two electrodes is 4cm. The gas used to produce plasma is argon gas which flows inside the chamber at a rate of 40 sccm. The influence of work function for different target materials (gold, copper, and silver), - 5cm in diameter and around 1mm thickness - different working pressures, and different applied voltages on electrical characteristics (discharge current, discharge potential, and Paschen’s curve) were studied. The results showed that the discharge cur
... Show More