Semiconductor quantum dots (QDs) have attracted tremendous attentions for their unique characteristics for solid-state lighting and thin-film display applications. A simple chemical method was used to synthesis quantum dots (QDs) of zinc sulfide (ZnS) with low cost. The XRD) shows cubic phase of the prepared ZnS with an average particles size of (3-29) nm. In UV-Vis. spectra observed a large blue shift over 38 nm. The band gaps energy (Eg) was 3.8 eV and 3.37eV from the absorption and photoluminescence (PL) respectively which larger than the Eg for bulk. QDs-LED hybrid devices were fabricated using ITO/ PEDOT: PSS/ Poly-TPD/ ZnS-QDs/ with different electron transport layers and cathode of LiF/Al layers. The EL spectrum reveals a broad emission band covering the range 350 - 700 nm. Current-voltage (I–V) characteristics indicate that the output current is good according to the few voltages (8, 10, 11 and 12 V) used which gives acceptable results to light generation. Using TPBi and Alq3 as electron transport layer gives good enhancement to light generation in compares with that of QDs only. The emissions causing the luminescence were identified depending on the chromaticity coordinates (CIE 1931).
This paper investigates the experimental response of composite reinforced concrete with GFRP and steel I-sections under limited cycles of repeated load. The practical work included testing four beams. A reference beam, two composite beams with pultruded GFRP I-sections, and a composite beam with a steel I-beam were subjected to repeated loading. The repeated loading test started by loading gradually up to a maximum of 75% of the ultimate static failure load for five loading and unloading cycles. After that, the specimens were reloaded gradually until failure. All test specimens were tested under a three-point load. Experimental results showed that the ductility index increased for the composite beams relative to the refe
... Show MoreIn this paper, effective slab width for the composite beams is investigated with special emphasis on the effect of web openings. A three dimensional finite element analysis, by using finite element code ANSYS, is employed to investigate shear lag phenomenon and the resulting effective slab width adopted in the classical T-beam approach. According to case studies and comparison with limitations and rules stipulated by different standards and codes of practice it is found that web openings presence and panel proportion are the most critical factors affecting effective slab width, whereas concrete slab thickness and steel beam depth are less significant. The presence of web opening reduces effective slab width by about 21%.
... Show MoreA Genetic Algorithm optimization model is used in this study to find the optimum flow values of the Tigris river branches near Ammara city, which their water is to be used for central marshes restoration after mixing in Maissan River. These tributaries are Al-Areed, AlBittera and Al-Majar Al-Kabeer Rivers. The aim of this model is to enhance the water quality in Maissan River, hence provide acceptable water quality for marsh restoration. The model is applied for different water quality change scenarios ,i.e. , 10%,20% increase in EC,TDS and BOD. The model output are the optimum flow values for the three rivers while, the input data are monthly flows(1994-2011),monthly water requirements and water quality parameters (EC, TDS, BOD, DO and
... Show MoreThe modern steer-by-wire (SBW) systems represent a revolutionary departure from traditional automotive designs, replacing mechanical linkages with electronic control mechanisms. However, the integration of such cutting-edge technologies is not without its challenges, and one critical aspect that demands thorough consideration is the presence of nonlinear dynamics and communication network time delays. Therefore, to handle the tracking error caused by the challenge of time delays and to overcome the parameter uncertainties and external perturbations, a robust fast finite-time composite controller (FFTCC) is proposed for improving the performance and safety of the SBW systems in the present article. By lumping the uncertainties, parameter var
... Show MoreBackground: The collagen triple helix repeat containing 1 (CTHRC1) protein has been connected to decreased levels of vitamin D and calcium, as well as obesity. This study aimed to investigate the relationship between CTHRC1 and osteoporosis in post-menopausal women and compare with healthy subjects. Subjects and Methods: A cross-sectional study consisted of 86 women were enrolled in this study and divided into three groups based on the results of dual-energy densitometry (DXA): 30 women with osteoporosis, 30 women with osteopenia, and 26 healthy women. Data on demographic and clinical features and laboratory values of Calcium (Ca) and Vitamin D3 (V.D3) were recorded. Results: Women with osteoporosis had significantly increased level
... Show MoreAbstract Background: Augmentation cystoplasty is one of the surgical procedure for treatment of spastic neurogenic bladder that has a significant improvement in the cystometric parameters. Aim of study: The aim of this study is to describe cystometric findings pre and post augmentation cystoplasty in patients with spastic neurogenic bladder. Patients and methods: A prospective study including patients aged 6-18years with neurogenic bladder operated on for augmentation cystoplasty surgery with ilium segments due to a neurogenic bladder from the years 2020–2024. A urodynamic study was conducted before and 3 months after the surgical procedure. Non-probabilistic sample of consecutive cases. Descriptive statistics were presented using fre
... Show MoreGlass Fiber Reinforced Polymer (GFRP) beams have gained attention due to their promising mechanical properties and potential for structural applications. Combining GFRP core and encasing materials creates a composite beam with superior mechanical properties. This paper describes the testing encased GFRP beams as composite Reinforced Concrete (RC) beams under low-velocity impact load. Theoretical analysis was used with practical results to simulate the tested beams' behavior and predict the generated energies during the impact loading. The impact response was investigated using repeated drops of 42.5 kg falling mass from various heights. An analysis was performed using accelerometer readings to calculate the generalized inertial load
... Show More