Benign prostatic hyperplasia (BPH) is a prevalent condition among elderly and middle-aged men characterized by symptoms such as dysuria, urinary incontinence, and frequent micturition. The gold standard procedure for relieving BPH symptoms is transurethral resection of the prostate (TURP). However, some patients undergoing TURP are at risk of developing urinary tract infections (UTIs) due to uropathogenic bacteria. This prospective study aimed to investigate post TURP bacteruria alongside with multifactoria risk factors that implicated postoperatively compared to preoperative and intraoperative periods. Ninety patients undergoing TURP and 30 control subjects were included in the study. Urine specimen for urine analysis from pateints were conducted on three occasions: (60 mid-stream urine and 30 catheterized urine samples) were taken preoperatively, (90 samples via cystoscopy) were taken intraoperastively, and (90 mid-stream urine samples after catheter removal) were taken at the third day post-TURP procedure. The study findings were analyzed in correlation with various pre-, intra-, and postoperative potential risk factors to underscores the vulnerability of BPH patients to UTIs, particularly during the postoperative recovery phase. The Escherichia coli was the most commonly isolated uropathogen preoperatively, while Pseudomonas aeruginosa emerged as the primary pathogen intra- and post-operatively. Several risk factors were identified as significantly associated with post-TURP bacteriuria. These include preoperatively, positive pre-operative culture analysis, diabetic patients, and preoperative catheterization. Additionally, intraoperative factors such as prolonged operation duration were also implicated. Postoperatively, persistent bacteriuria was significantly linked with the duration of catheterization. In conclusion, the findings highlight the complex interplay of factors contributing to post-TURP UTIs and stresses the significance of thorough risk evaluation and customized preventative measures to reduce infection risks among BPH patients undergoing TURP.
The present work focuses on the experimental implementation of one of the fiber optical sensors, the optical glass fiber built on surface Plasmon resonance. A type of optical glass fiber was used in this work, single-mode no-core fiber with pre-tapering diameter: (125.1 μm) and (125.3 μm), respectively. The taper method can be tested by measuring the output power of the optical fiber before and after chemical etching to show the difference in cladding diameter due to the effect of hydrofluoric acid with increasing time for the taper process. The optical glass fiber sensor can be fabricated using the taper method to reduce the cladding diameter of the fibers to (83.12 µm, 64.37 µm, and 52.45 µm) for single-mode fibers using Hydrofluoric
... Show MoreMicrobiological contamination by fungi impacts the quality and safety of wheat grain storage. This study aimed to evaluate the efficacy of cold plasma in restricting the growth of the fungus, Aspergillus niger, which was isolated from wheat grains. A dielectric barrier discharge (DBD) operating at atmospheric pressure generated cold plasma that was used to treat the fungus, and the impact of this treatment was investigated at various periods 1, 2, 4, 6, and 15 minutes. The results revealed a highly significant decrease in the growth and number of spores of Aspergillus niger compared to the controls. This study revealed an efficient technique for enhancing wheat grain storage that could be a foundation for further large-scale studies.
... Show MoreTheoretical and experimental investigations of free convection through a cubic cavity with sinusoidal heat flux at bottom wall, the top wall is exposed to an outside ambient while the other walls are adiabatic saturated in porous medium had been approved in the present work. The range of Rayleigh number was and Darcy number values were . The theoretical part involved a numerical solution while the experimental part included a set of tests carried out to study the free convection heat transfer in a porous media (glass beads) for sinusoidal heat flux boundary condition. The investigation enclosed values of Rayleigh number (5845.6, 8801, 9456, 15034, 19188 and 22148) and angles of inclinations (0, 15, 30, 45 and 60 degree). The numerical an
... Show MoreAs a result of the exacerbation of the problem of water pollution, research was directed towards studying the treatment using ceramic membranes, which proved to be highly effective in treating all water sources. The research aims to study the possibility of preparing a new type of ceramic membranes from Syrian zeolite that was not previously used in this field. In this research, ceramic membranes were prepared from Syrian raw zeolite in several stages. Zeolite sample was characterized, grinded, mixed with boric acid, pressed to form desks, treated thermally according to experiment program, finally coated with silver nanoparticles. Specifications of prepared membranes were determined according to reference methods, effectiveness of prepar
... Show MoreThe study aimed to evaluate Glucagon-Like Peptide-1 levels in Polycystic ovary syndrome (PCOS) infertile female with Diabetes Mellitus (DM) and compare the results with control group, also, to find the correlation for GLP-1 with Luteinizing hormone (LH), Follicle stimulating hormone (FSH) and LH/FSH ratio that may be used in prediction atherosclerosis in these patients. The study included nineteen women with age ranged (30-40) years and BMI ranged between (30-35) Kg/m 2. Subjects were divided into two groups: group (1) consist of (45) females as a healthy control and group (2) consist of (45) infertile females with PCOS and DM as complication. Fasting serum glucose was determined by using commercial kits (Biolabo SA-France); LH, FSH, prolac
... Show MoreThe purpose of this paper is to apply styrene butadiene rubber (SBR) as virgin alongside expanded polystyrene (EPS) resin as a recycled polymer after consumption in the presence of bagasse fibers (BF) as biomass source derived from sugarcane in different concentrations to reinforce this polymeric matrix to form affordable composites that can be used in manufacturing low-cost and sustainable car interior-trim constituents.
SBR and EPS represent an example for thermoplastic elastomers (