Thin films of pure yttrium oxide (Y₂O₃) and doped with cerium oxide (CeO₂) were prepared by the chemical spray pyrolysis(CSP)method. The structural, optical and electrical properties of the prepared films were investigated. The analysis of X-ray diffraction (XRD) thin films revealed that the undoped and doped Y₂O₃  were amorphous with a broad hump around 27^o and narrow humps around 48^o and 62^o for all samples. Except for the Y₂O₃:6wt.%CeO₂ thin film, all had signal preferential orientation along the (100) plane at 2θ=12.71^o which belongs to CeO₂, Field emission scanning electron mic

     The study area lies in Wasit governorate south west Kut city, where Al Ahdeb oil field is located to the south of Al Ahrar district. The present study deals with assessment of heavy metals pollution in water by collecting eleven water samples (five samples from drainage and six samples from surface water) in 5^th of December 2016. The water samples analysis of heavy elements in the study area shown that water is polluted with high concentration of (Pb, Cd) elements, while the concentration of (Cu, Fe, Zn) in water samples are within the permissible limits of both World Health Organization, and Iraqi standards and there are no hazard effects from these elements. The study detected some diseases that inju

A single-crystalline semi-polar gallium nitride (11-22) was grown on m-plane (10-10) sapphire substrate by metal organic chemical vapor deposition. Three-step approach was introduced to investigate the grain size evolution for semi-polar (11-22) GaN. Such approach was achieved due to the optimized gallium to ammonia ratio and temperature variations, which led to high quality (11-22) oriented gallium nitride epilayers. The full width at half maximum values along (-1-123) and (1-100) planes for the overgrowth temperature of 1080°C were found to be as low as 0.37° and 0.49°, respectively. This was an indication of the enhanced coalescence and reduction in root mean square roughness as seen by atomic force microscopy. Surface analysi

Burnishing improves fatigue strength, surface hardness and decrease surface roughness of metal because this process transforms tensile residual stresses into compressive residual stresses. Roller burnishing tool is used in the present work on low carbon steel (AISI 1008) specimens. In this work, different experiments were used to study the influence of feed parameter and speed parameter in burnishing process on fatigue strength, surface roughness and surface hardness of low carbon steel (AISI 1008) specimens. The first parameter used is feed values which were (0.6, 0.8, and 1) mm at constant speed (370) rpm, while the second parameter used is speed at values (540, 800 and 1200) rpm and at constant feed (1) mm. The results of the fatigue

Background: Diabetes and hypertension are related to cardiovascular risk factors and are possible to detect development of atherosclerosis in cardiovascular system, were can predict their effect and measurement by ultrasound and Doppler study. These risk factors included increased intima-media thickness, resistive index (RI) and pulsatility index (PI) of the right common carotid arteries. Method: We studied 20 patients with diabetes and hypertension, and 20 patients with diabetes only, were examine right carotid arteries for these two groups. In this sample we studied the Lumen diameter of the Rt. carotid arteries, Intima – media thickness (IMT), peak systolic velocity, end diastolic velocity, and Pulsatility index, Resistance index were

Objectives: The study aims at:
1- Measuring the level of lead in workers’ saliva and blood in the factory.
2- Studying the correlation between the saliva lead level and the infection that caused by microorganisms, isolation and
identification.
3-Studying the influence of high blood lead level on the total white blood cells.
Methodology: This study has been conducted for the period from March 15th, 2010 to May, 20th
, 2010. A total of (60)
saliva and blood samples were collected from workers in batteries industry factory in Baghdad and another (20) samples
were collected as a control group. Lead level had been measured in blood and saliva samples, then microorganisms were
isolated the from the saliva samples.

Out of 180 children, 60 (33.3%) have Amoebiasis infection as diagnosed by direct wet smear and Saturated Salt Solution (SSS). SSS method is more significant (P=0.001) in diagnosis of the disease. Number of children infected with Amoebiasis infection is higher in infants aged 1-6 months, but without any significant difference to ages 6-12 or 12-18 months. In contrast, infants aged 18-24 months are significantly differant (P=0.01) as the infection rate is 16.6%. Gender also is seen to be reduced in significance (P= 0.001) for females aged 18-24 months. Blood profile of the involved infants has shown a significant variation (P=0. 01) for all blood profile parameters (RBC (P=0.05), WBC (P=0.001), Lymphocytes (P=0.05), Granulated WBC (P=0.05),

Prodigiosin, is a natural red pigment produced by various bacteria that firstly
characterized from Serratia marcescens. It is an alkaloid secondary metabolite with
a unique tripyrrol structure.This pigment is a promising drug owing to its reported
characteristics of having antifungal, immunosuppressive and anti-cancer activity. In
this study prodigiosin was produced by Serratia marcescens., which was isolated
from soil identified and characterized by morphology, Gram’s staining, biochemical
and carbohydrate fermentation tested and confirmed by the API 20E test.
From these samples, six isolates of Serratia marcescens( 24) % were obtained out
of 25 soil samples. Ability of these isolates in prodigiosin production

Research aims to develop a novel technique for segmental beam fabrication using plain concrete blocks and externally bonded Carbon Fiber Reinforced Polymers Laminates (CFRP) as a main flexural reinforcement. Six beams designed an experimentally tested under two-point loadings. Several parameters included in the fabrication of segmental beam studied such as; bonding length of carbon fiber reinforced polymers, the surface-to-surface condition of concrete segments, interface condition of the bonding surface, and thickness of epoxy resin layers. Test results of the segmental beams specimens compared with that gained from testing reinforced concrete beam have similar dimensions for validations. The results show the effectiven

Semiconductor-based metal oxide gas detector of five mixed from zinc chloride Z and tin chloride S salts Z:S ratio 0, 25, 50, 75 and 100% were fabricated on glass substrate by a spray pyrolysis technique. With thickness were about 0.2 ±0.05 μm using water soluble as precursors at a glass substrate temperature 500 ºC±5, 0.05 M, and their gas sensing properties toward CH4, LPG and H2S gas at different concentration (10, 100, 1000 ppm) in air were investigated at room temperature which related with the petroleum refining industry.
Furthermore structural and morphology properties were scrutinize. Results shows that the mixing ratio affect the composition of formative oxides were (ZnO, Zn2SnO4, Zn2SnO4+ZnSnO3, ZnSnO3, SnO2) ratios ment