Ankylosing spondylitis (AS) represents one kind of advanced arthritis formed via inflammatory stimuli long-term in the spin‘s joints. Interleukin (IL)-29 (interferon- lambda1(IFN- λ1)), interleukin (IL)-28A (interferon- lambda 2 (IFN- λ2)) and interleukin (IL)-28B (interferon- lambda 3(IFN-λ3)) are three interferon lambda (IFN- λs) molecules that have recently been identified as new members of the IFN family. IL-28B expression in ankylosing spondylitis (AS) is not well understood. 150 male healthy controls ((HC) and 160 males with AS as patients group participated in this study. Serum level and gene polymorphism were assessed using an enzyme-linked immunosorbent assay and Sanger sequencing for IL-28B, respectively. The results showed significantly lower serum IL-28B concentrations in the AS groups in comparison to the HC groups (both p values equal to 0.003). There was a large difference in IL-28B genotype and allele frequency between the two individuals. IL-28B heterozygote genotype CT of rs12979860 SNP exhibits a substantial correlation with AS (P = 0.008). While the genotypes of rs12980275 SNP were not shown any significant correlation with AS. The findings suggest that serum concentration of IL-28B is a potential diagnostic biomarker in patients with AS, and that the heterozygote CT of rs12979860 SNP serves as a potential risk factor for the onset of AS in the Iraqi population. Keywords: ankylosing spondylitis, autoimmune disease , IL-28B, single nucleotide polymorphism
(21)
(15)
(2)
(2)
This study evaluates the flexural behavior of ultra-thin (50 mm) one‑way reinforced‑concrete (RC) slabs retrofitted with near‑surface mounted (NSM) carbon‑fiber‑reinforced polymer (CFRP) rods under quasi‑static loading. T300‑grade CFRP rods (≈4 mm diameter) were bonded in pre‑cut 7 mm × 7 mm grooves using a two‑part epoxy. As a proof-of-concept experimental baseline, three simply‑supported specimens (1000 mm × 500 mm × 50 mm) were tested in a six‑point bending configuration (four applied loads + two reactions): two conventional controls and one strengthened slab. A load‑control rate of ~15 kN/min was applied; the controls were cycled twice and the strengthened slab four times. Relative to the average of
... Show More
Dyes are extensively water-soluble and toxic chemicals. The disposing of wastewater rich with such chemicals has severely impacted surface water quality (rivers and lakes). In the current study, an anionic dye, methyl orange, were extracted from wastewater fluids using bulk liquid membranes supplemented with an anionic carrier (Aliquat 336 (QCI)). Parameters including solvent type (carbon tetrachloride and chloroform), membrane stirring speed (100-250 rpm), mixing speed of both phases (50-100 rpm), The feed pH (2-12) and implemented temperature (35-60 °C) were thoroughly analyzed to determine the effect of such variables on extraction effectiveness. Furthermore, the effect of methyl orange (10-50 ppm) in the feed stage and NaOH (0
... Show More
(7)
(1)
(50)
(49)
In this work, the effect of aluminum (Al) dust particles on the DC discharge plasma properties in argon was investigated. A magnetron is placed behind the cathode at different pressures and with varying amounts of Al. The plasma temperature (Te) and density (ne) were calculated using the Boltzmann equation and Stark broadening phenomena, which are considered the most important plasma variables through which the other plasma parameters were calculated. The measurements showed that the emission intensity decreases with increasing pressure from 0.06 to 0.4 Torr, and it slightly decreases with the addition of the NPs. The calculations showed that the ne increased and Te decreased with pressure. Both Te and ne were reduced by increasing
... Show More
(14)
(13)
(1)
(1)