Abstract

There has been a heated controversy over the role the financial policy plays and how sufficient   it   is   in affording   the   financial   burden. This   burden   is   known as the operational   current expenses   which   the   governments   of   various countries mainly afford,   despite the   discrepancy   in   the   government’s   economic   policy.   After   the deterioration and deficit in the state budget in all countries nowadays, it was necessary to find an appropri

The aim of this research is analysis the effect of the changes in (GDA, g, inflation) at average and standard economic curriculum in composition of the models, depending on SPSS program in analysis, and according to available date from central bank of Iraq and during the period from 2003 to 2018 and by using OLS and estimate of the equation and the results showed a statistical significance relation in incorporeal level 5% and the R² value equal  to 92.1 refer to the changes in independent variables explain 92% of changes of unemployment and the independent variables effect are very limit depend on estimated parameters in the model and respectively (0.986,0.229,-0.060), the research recommended necessity to active the inve

some ecological (physical and chemical varible) of water samples were studies monthly from December 2008 to May 2009 at two stations( St.1) Al - Chibayesh marsh and (St.2) Abu – Zirik marsh which are located in the south of Iraq . These variables included : Temperature, pH, EC, Dissolved oxygen , Total alkalinity, Nitrate, Sulphate, and phosphate, Si-SiO2 and Ca ,Mg, Cl, The marsh Considered as fresh water and alkaline. Abu-Zirik less than Al-Chibayesh.

The research studies the main variables for the concept of sharing in knowledge in one of the most important control agencies in Iraq, which is (The Federal Board of Supreme Audit). Also, the quality of the controlling businesses by the Board in light of the major challenges that facing the fight against signs of cheating and administrative and financial corruption for offices submitted to controlled and auditing, with the increasing and intensification of these appearances. In order to enable the Board to cope with this situation, has to be thinking hard about how to achieve excellence, progress and development to face these situations, through the application of sharing in knowledge for the financial controller, and then achiev

This study detects the presence of an important flavonoid "Casticin" in the fruits of Vitex agnus-castus L. grown in Iraq. The pharmaceutical importance of Casticin arise from its consideration as anti-tumor substance and have cytotoxic effects, and the absence of any study concerning Casticin content of this medicinal plant in Iraq, gave this study its importance. This study concerned with the extraction, identification, isolation and purification  of Casticin from the fruits of Vitex agnus-castus L. The extraction of this compound was carried out using  two methods. Identification of this compound was done by Thin Layer Chromatography (TLC) in which three different solvent system has been tried. This identif

This study detects the presence of the most important steroidal sapogenin “Tigogenin” in the leaves of Yucca aloifolia widely cultivated in Iraq. The absence of any study concerning the Tigogenin content of this medicinal plant in Iraq, and the industrial importance of Tigogenin depending on its role as a precursor in the synthesis of some steroidal drugs, acquired this study its value. This study concerned with extraction, identification, isolation, and purification of Tigogenin from the leaves of Yucca aloifolia. Extraction of this compound was carried out using two methods. Identification of this compound was done using thin layer chromatography (TLC) where different solvent systems had been tried. Liberm

The presence of the most important steroidal sapogenin “Tigogenin” in the leaves of Agave americana  cultivated in Iraq was detected. The absence of any study concerning the Tigogenin content of this medicinal plant in Iraq, and the industrial importance of Tigogenin depending on its role as a precursor in the synthesis of some steroidal drugs, acquired this study its value. This search include extraction,  isolation,  purification and dentification of Tigogenin from the leaves of Agave americana. Extraction of this compound was carried out using two methods. Identification of this compound is carried out by using thin layer chromatography (TLC) where three different mobile phase have been use

Galantamine was isolated from the bulb part of Narcissus jonquilla L. plant cultivated in Iraq. The compound was identified by different chemical analysis like: Fourier Transforms Infrared spectra (FTIR), High Performance Liquid Chromatography (HPLC) and mass spectroscopy and 1H-NMR.

This paper studied the behaviour of reinforced reactive powder concrete (RPC) two-way slabs under static load. The experimental program included testing three simply supported slabs of 1000 mm length, 1000 mm width, and 70 mm thickness. Tested specimens were of identical properties except their steel fibers volume ratio (0.5 %, 1 %, and 1.5 %). Static test results revealed that, increasing steel fibers volume ratio from 0.5% to 1% and from 1% to 1.5%, led to an increase in: first crack load by (32.2 % and 52.3 %), ultimate load by (36.1 % and 17.0 %), ultimate deflection by (33.6 % and 3.4 %), absorbed energy by (128 % and 20.2 %), and the ultimate strain by (1.1 % and 6.73 %). The stiffness and ductility of the specimens also increased. A

Incremental Sheet Metal Forming (ISMF) is a modern sheet metal forming technology which offers the possibility of manufacturing 3D complex parts of thin sheet metals using the CNC milling machine. The surface quality is a very important aspect in any manufacturing process. Therefore, this study focuses on the resultant residual stresses by forming parameters, namely; (tool shape, step over, feed rate, and slope angle) using Taguchi method for the products formed by single point incremental forming process (SPIF). For evaluating the surface quality, practical experiments to produce pyramid like shape have been implemented on aluminum sheets (AA1050) for thickness (0.9) mm. Three types of tool shape used in this work, the spherical tool ga