Coal fines are highly prone to be generated in all stages of Coal Seam Gas (CSG) production and development. These detached fines tend to aggregate, contributing to pore throat blockage and permeability reduction. Thus, this work explores the dispersion stability of coal fines in CSG reservoirs and proposes a new additive to be used in the formulation of the hydraulic fracturing fluid to keep the fines dispersed in the fluid. In this work, bituminous coal fines were tested in various suspensions in order to study their dispersion stability. The aggregation behavior of coal fines (dispersed phase) was analyzed in different dispersion mediums, including deionized-water, low and high sodium chloride solutions. Furthermore, the effect of Sodium Dodecyl Benzene Sulfonate (SDBS), an anionic surfactant, on fine aggregation in the suspensions was investigated over a wide alkaline range. At a known pH, the results of stability were validated with the proppant pack glass column test and further verified with microscopic images. It was observed that adding SDBS to the hydraulic fracturing fluid keeps the coal fines well-dispersed in the post-hydraulic fracturing flow back and prevents coal fines aggregation, and ultimately helps permeability enhancement. The results show that at a constant pH, as salinity increases, the zeta-potential (an indirect indicator of stability of the coal-water slurry) reduces. Also, a trace amount of SDBS substantially enhances the dispersion stability of coal fines. This enhancement dictates that coal fines will not congregate and will not plug the proppant pack. Furthermore, the results were confirmed by proppant pack glass-column tests and microscopic images, the result of which illustrate much less aggregation when having SDBS added to the suspension. Polymeric surfactants have been used in the field to disperse coal fines. However, it causes the coal matrix to swell and clog the pore throats, thus reducing the permeability. The anionic surfactant, SDBS, has never been tried in field applications to disperse coal fines. The current research demonstrates the considerable potential of SDBS, as a hydraulic fracturing fluid additive, in enhancing the dispersion stability of the coal fines.
The sewage water is the main sources of pollution for the Tigris river for that reason this study was done,The ability of nature treatment were examined along the path of alkarazi valley which was covered with reed plant also the phytoremidation were examined at the establish unit(surface flow system) which was vegetative with the plant Eichhornia crassipes .The result shows that elements which can be removed by precipitation efficiency removal like turbidity where its removal percentage at the unit of treatment reached 95.2 %where the percentage of removal through the Alkarazi was 50.4%.The removal percentage of E.coli at the unit was 90.2% where the percentage of removal through the Alkarazi was 52%.The biological oxygen demand removal
... Show MoreIn this study a DFT calculation on cyclopropanone, cyclopropandione and cyclopropantrione molecules was performed using the basis function 6-31G ** / MP2 and exchange correlation potential B3-LYP. The results showed that the ground state of all molecules geometry belong to the point group ð¶2ð‘£where a vibronic coupling between the vibrational motion with the electronic ground state in the molecule C3O3 this leads to a reduction in symmetry of the molecule fromð·3â„Žto ð¶2ð‘£, the driving force of this process is accessing to the electronic configuration complies with Hückel aromatic systems with two electrons. Also in this, study the normal modes of vibration, frequencies, intensities and symm
... Show MoreIn recent years, there has been a very rapid development in the field of clean energy due to the huge increase in the demand, which prompted the manufacturers and the designers to increase the efficiency and operating life of the energy systems and especially for wind turbine. It can be considered that the control unit is the main key of the wind turbines. Consequently, it’s essential to understanding the working principle of this unit and spotlight on the factors which influence significantly on the performance of wind turbine system. Simulink technique is proposed to find the response of the wind turbine system under different working conditions. In this paper, it was investigated
In this research, the focus was on estimating the parameters on (min- Gumbel distribution), using the maximum likelihood method and the Bayes method. The genetic algorithmmethod was employed in estimating the parameters of the maximum likelihood method as well as the Bayes method. The comparison was made using the mean error squares (MSE), where the best estimator is the one who has the least mean squared error. It was noted that the best estimator was (BLG_GE).
This paper presents a numerical simulation of the flow around elliptic groynes by using CFD software. The flow was simulated in a flume with 4m long, 0.4m wide, and 0.175m high with a constant bed slope. Moreover, the first Groyne placed at 1m from the flow inlet with a constant the Groyne height of 10cm and a 1cm thickness, and the width of Groynes equals 7cm. A submergence ratio of the elliptic Groynes of 75% was assumed, corresponding to a discharge of 0.0057m3/sec. The CFD model showed a good ability to simulate the flow around Groynes with good accuracy. The results of CFD software showed that when using double elliptic Groy
... Show MoreObjective: Evaluation of the poly ether keton keton polymer (PEKK) coating material on the commercial pure titanium disks (CP Ti) with or without laser surface structuring. Design: In vitro experimental study of PEKK polymer coated material on the CP Ti disks with or without laser surface structuring. Materials and methods: coating the surface of the commercial pure titanium (CP Ti) disks with PEKK polymer was performed via using frictional mode CO2 laser, then the samples disks analyzed by using FESEM. Results: the FESEM reveal good adherence and distribution of the PEKK coated material over the CP Ti substrate by using the frictional mode CO2 laser at 2 watt and 6 ms pulse duration. Conclusion: the frictional mode CO2 laser considered an
... Show MoreAn atomic force microscope (AFM) technique is utilized to investigate the polystyrene (PS) impact upon the morphological properties of the outer as well as inner surface of poly vinyl chloride (PVC) porous fibers. Noticeable a new shape of the nodules at the outer and inner surfaces, namely "Crater nodules", has been observed. The fibers surface images have seen to be regular nodular texture at the skin of the inner and outer surfaces at low PS content. At PS content of 6 wt.%, the nodules structure was varied from Crater shape to stripe. While with increasing of PS content, the pore density reduces as a result of increasing the size of the pore at the fiber surface. Moreover, the test of 3D-AFM images shows that the roughness of both su
... Show More