Kiffil Shinafiya project was selected as it’s been conducted and covering the areas of grain crops agriculture in Najaf and Qadissiya provinces. Lands of this project are considered as a part of the Mesopotamian plain located in between N32⁰ 15′, N31⁰ 30′ and E44⁰ 44’, E44⁰ 20′. Three hydrosequences were disclosed with three transects (T1, T2, T3) in the area of study. The first hydrosequence was perpendicular on the other two sequences. Fifteen pedons were outcropped, five pedons in each transect in addition to eighteen more surface samples to be a total samples of 33 locations. Pedons were morphologically described due to soil survey manual (Soil Survey Staff, 2017). Spatial distribution of soil salinity showed that the largest area was for the class 4-8 dS.m-1, while sodium adsorption ratio ranged from 1.05-55.58 where the highest value was in the second pedon of the first transect. Also, pH of soil showed weak spatial variability due to the range it is included in calcareous soils between 7.02 up to 8.57. Carbonate minerals showed simple variation as well in the area of study in a range of 114.15-494.37 gm.kg-1 in the surface horizons and samples where the highest content was in the third pedon of the first transect. Map of spatial distribution showed that there is a similarity between both of organic matter an organic carbon, where the highest content of the organic matter and carbon was in the thirteenth pedon of the third transect at 21.85 gm.kg-1 and 12.70 gm.kg-1 respectively. Total nitrogen showed highest content of 0.16% in the sixth pedon of the second transect and the thirteenth pedon of the third transect of the hydrose-quences. Available nitrogen, phosphorus, and potassium content in soil showed that the highest content of available nitrogen was 77.00 mg.kg-1 in the tenth pedon of the second transect which is located at the end of the hydrosequence, while available phosphorus of the highest value was in the fifth pedon of the first transect that is located at the highest part of the hydrosequence of that transect, and the available potassium did not show a specific distribution spatially.
(8)
(4)
Porous Silicon (PSi) has been produced in this work by using Photochemical (PC) etching process by using a hydrofluoric acid (HF) solution. The irradiation has been achieved using quartz- tungsten halogen lamp. The influence of various irradiation times on the properties of PSi اmaterial such as layer thickness, etching rate and porosity was investigated in this work too.
The XRD has been studied to determine the crystal structure and the crystalline size of PSi material
This paper examines the mechanical properties of a composite material made of modified Iraqi gypsum (juss) reinforced with polypropylene fibers. The modified juss was prepared by adding two percentages of cement (5, 10) %. Two percentages of polypropylene fibers were used, to reinforce the modified juss (1, 2) %. The water/dry compound ratio used was equal to 0.53%. The composite was evaluated based on compressive strength, flexural strengths, absorption percentage, density, acoustic impedance, ultra - pulse velocity, longitudinal shrinkage and setting time tests. The results indicated that the inclusion of cement on to juss increases the compressive strength, absorption percentage, density, acoustic impedance, ultra - pulse velocit
... Show More
Background: Polymer surfaces usually present problems in bonding and finishing due to their low hydrophilicity. The aim of this study is to investigate the effect of plasma treatment with the use of two types of gases (oxygen and argon) on surface roughness, and chemical surface properties of acrylic resin denture base polymer material. Materials and Methods: Three heat cured acrylic resin specimens of (2*8*30 mm) dimensions were prepared for each test carried out in this study. Two tests were conducted, surface roughness test and chemical surface analysis test. Results: Application of plasma treatment increased surface roughness for both oxygen and argon plasma treated acrylic resin specimen groups compared with control untreated group,
... Show More
(3)
(1)
This research aims to investigate and evaluate a reactive powder concrete (RPC) cast using economical materials. Its mechanical properties were investigated and evaluated by studying the effects of using different cement and silica fume contents and locally steel fibers aspect ratios as reinforcement for this concrete. A compressive strength of about 155.2MPa, indirect tensile strength of 16.0MPa, modulus of elasticity of 48.7GPa, flexural strength of 43.5MPa, impact energy of 3294.4kN.m and abrasion loss 0.59% have been achieved for reinforced RPC contains 910 kg/m3 cement content, silica fume content 185 kg/m3 of cement weight and fiber volume fraction 2%. The water absorption values w
... Show MoreAbstract:Porous Silicon (PSi) has been produced in this work by using Photochemical (PC) etching process by using a hydrofluoric acid (HF) solution. The irradiation has been achieved using quartz- tungsten halogen lamp. The influence of various irradiation times on the properties of PSi اmaterial such as layer thickness, etching rate and porosity was investigated in this work too. The XRD has been studied to determine the crystal structure and the crystalline size of PSi material
Assume that G ≅ HN the Harada–Norton group. In this paper, effective investment for the graph ΓRI HN standard features to acquire meaningful algebraic results for the graph ΓRI HN and its corresponding group HN. For instance, marketing a modern methods to understand the way of create a precise small subgroups in G. Furthermore, performing a full investigation for getting particular ΓRI HN parameters.
Background: Denture lining materials are widely used in prosthodontic treatment and management of traumatized oral mucosa. A contaminated prosthesis can provide a source of cross-contamination between patients and dental personnel as well as a cause for denture stomatitis. Therefore, denture disinfection has been recommended as an essential procedure for maintenance of a healthy oral mucosa. This study investigated the effect of SOLO disinfectant solution on some properties of different denture lining materials. Materials and methods: Three different solutions were used in this study; SOLO disinfectant solution, sodium hypochlorite solution, and water on three types of acrylic denture lining materials; hot cure, cold cure, and soft acrylic
... Show MoreSelf-compacted concrete (SCC) is a highly flowable concrete, with no segregation which can be spread into place by filling the structures framework and permeate the reinforcement without any compaction or mechanical consolidation ACI 237R-14. One of the most important problems faced by concrete industry in Iraq and Gulf Arab land is deterioration due to internal sulfate attack (ISA) that causes damage of concrete and consequently reduces its compressive strength, increases expansion and may lead to its cracking and destruction. The experimental program was focused to study two ordinary Portland cements with different chemical composition with (5, 10 and 15) % percentage of high reactivity metakaoline (HRM)
... Show More