Abstract:

This research sheds light on the major sins (fornication and sodomy) as two crimes that are prohibited by the divine laws, including its conclusion by the Islamic Sharia. Major sins so that life and the universe are organized, and the individual lives a life of chastity and purity free of filth and filth. The Islamic message included a set of preventive measures and remedial methods that, if the ummah were to apply them, they would live a decent life full of noble goals.

In this research is to study the influence of the aging heat treatment on the pitting corrosion resistance of martensitic stainless steel (MSS), where a number of specimens from martensitic stainless steel were subjected to solution treatment at 1100 ^oC for one hour followed by water quenching then aging in the temperatures range (500-750) ^oC for different holding times (1,5,10,15&20) hr. Accelerated chemical corrosion test and immersion chemical corrosion test were performed on samples after heat treatment. The results of the research showed that the pitting corrosion resistance is significantly affected by the aging temperature. Where found that the aging samples at a temperature of 500 °C have the highest ra

One of the most important phenomenon that occurs in sheet metal forming processes is the spring-back, which causes several geometrical alterations in the parts. The accurate prediction of springback after bending unloading is the key to the tool design, operation control, and precision estimate concerning the part geometry. This study investigated experimentally the effect of pretension in three rolling direction (0, 90, 45 degree) on the springback behavior of the yellow brass, sheet under V shape bending die. The pre-tension ranges from five different levels starting of 11% to 55% from the total strain in each rolling direction by regular increase of 11 %, then bent on a V-die 90 degree for the springback estimate. From experiment the

      In this paper, the researcher suggested using the Genetic algorithm method to estimate the parameters of the Wiener degradation process,  where it is based on the Wiener process in order to estimate the reliability of high-efficiency products, due to the difficulty of estimating the reliability of them using traditional techniques that depend only on the failure times of products. Monte Carlo simulation has been applied for the purpose of proving the efficiency of the proposed method in estimating parameters; it was compared with the method of the maximum likelihood estimation. The results were that the Genetic algorithm method is the best based on the AMSE comparison criterion, then the reliab

المستخلص: إن اغتيال المدن الاثرية كان ولايزال مستمرا بطريقة او باخرى بشكل يؤدي الى ضياع ملاح المدينة القديمة بتغطيتها بالابنية والعمائر الحديثة نتيجة النمو الحضري الغير منتظم دون مراعة الحالة الاثرية للمدينة فتندثر اغلب معالمها وتغطى يشكل لايعود بالامكان الاستمتاع بجمال الماضي، هذا كان الدافع الرئيسي لتقديم هذه الدراسة الاثرية العلمية المعتمدة على احدث البرامجيات العلمية في عمل الخرائط التوضيحية(AR

   This research aims to introduce the general tax on sales in gordan and the most important concepts related to this type of taxes and identify the  most  on characteristics and stand on its role in supplying the general budget of the necessary fundig to cover the over head of the state and the factorsinfluencing it and whether such a tax has been able to chieve the desired goals.including in contribute to an important and growing role in puplic revenues or not to be able to achieve these goals through the use of descriptive and analytical technique based on the data and information relevant.wasreached some conclusion and  recommendations was most important is that the general sales tax comes in

The tax revenues achieved through projects of transition to private sector are regarded as an important source for using in achieving political, economic and social objectives. Since Iraq is heading towards free market economy, new strategies should be adopted to reform the taxation system from by a qualified taxation management office and to activate the taxation policy and to reconsider legislation in relation to the aware of the legible to the importance of disclosure of their taxable real income in order to arrive at contribution of privatization in the taxation revenues for the important role effect on economic activities. In the light of the above, the research is based upon a hypothesis which stipulates that privatization contribu

Abstract

This paper concerned with study the effect of a graphite micro powder mixed in the kerosene dielectric fluid during powder mixing electric discharge machining (PMEDM) of high carbon high chromium AISI D2 steel. The type of electrode (copper and graphite), the pulse current and the pulse-on time and mixing powder in kerosene dielectric fluid are taken as the process main input parameters. The material removal rate MRR, the tool wear ratio TWR and the work piece surface roughness (SR) are taken as output parameters to measure the process performance. The experiments are planned using response surface methodology (RSM) design procedure. Empirical models are developed for MRR, TWR and SR, using the analysis

Objective(s): assessment of  the health follow up and weight control for women with osteoporosis and find out the relationship between their health follow up and weight control and their socio-demographic characteristics.

Methodology: A descriptive study was conducted on women with osteoporosis for the period of September, 26^th 2020 to Jun, 20th 2021. Non- probability (convenient) sample of (70) women with osteoporosis selected from (5) Private Clinics for Joints and Fractures in Baqubah City. A questionnaire was designed though extensive review of literatures and it consists of three parts: the first part includes women’s socio demographic characteristics, the second part inclu

Electrochemical Machining is a term given to one of nontraditional machining that uses a chemical reaction associated with electric current to remove the material. The process is depending on the principle of anodic dissolution theory for evaluating material removal during electrochemical process. In this study, the electrochemical machining was used to remove 1 mm from the length of the a workpiece (stainless steel 316 H) by immersing it in to electrolyte (10, 20 and 30 g) of NaCl and Na₂SO₄ to every (1 litter of filtered water).  The tool used was made from copper. Gap size between the workpiece and electrode is (0.5) mm. This study focuses on the effect of the changing the type and concentration of electroly