With increasing population and development, the resources of fossil fuels decreased, leading to the need to find alternative sources of energy. Furthermore, the use of fossil fuels is accompanied by several downsides including environmental fatality associated with toxic gas emissions from diesel engines and continuous increase of the price of diesel fuel. Biodiesel is one of the most important types of renewable energy that replaces the fossil fuel requirement (mineral diesel) and maintains eco-friendly sustainability. Calcium is an essential plant nutrient as it plays an important role in the formation of plant cell walls and membranes. Therefore, the fallen leaves of mango tree can be utilized to produce nano calcium oxide and serve as a highly effective catalyst in the transesterification process for biodiesel production. The green approach of mango leaves extract is more cost-effective, nontoxic, and environmentally friendly compared to other ways such as chemical and physical procedures. Transesterification reaction was conducted at fixed parameters of 65 ℃ reaction temperature, 3 wt.% catalyst concentration, 1.5 h reaction time, and 50% alcohol to oil weight ratio. The effects of several other parameters on the transesterification reaction were studied such as the volume of the reaction mixture, mixing speed, FFA% content, and methanol/ethanol weight ratio. The study found that methanol is more effective than ethanol as alcohol in transesterification reaction, and the FFA% has a slight effect on the catalyst to 1.8% FFA. The produced biodiesel was characterized by GC-MS and FT-IR analysis which indicate the presence of esters. The physical and fuel characteristics of the produced biodiesel were measured; it had a viscosity of 3.708 mm2/s, a density of 0.88869 g/cm3, and a flash point of 108 °C.
The research aims to determine the mix of production optimization in the case of several conflicting objectives to be achieved at the same time, therefore, discussions dealt with the concept of programming goals and entrances to be resolved and dealt with the general formula for the programming model the goals and finally determine the mix of production optimization using a programming model targets to the default case.
Nasryia oil field is located about 38 Km to the north-west of Nasryia city. The field was discovered in 1975 after doing seismic by Iraqi national oil company. Mishrif formation is a carbonate rock (Limestone and Dolomite) and its thickness reach to 170m. The main reservoir is the lower Mishrif (MB) layer which has medium permeability (3.5-100) md and good porosity (10-25) %. Form well logging interpretation, it has been confirmed the rock type of Mishrif formation as carbonate rock. A ten meter shale layer is separating the MA from MB layer. Environmental corrections had been applied on well logs to use the corrected one in the analysis. The combination of Neutron-Density porosity has been chosen for interpretation as it is c
... Show MoreThis study was conducted to determine the effects of concentration of hydrochloric acids, temperature, and time on the hydrolysis of soya proteins (defatted soya flour) by determining the value of total protein nitrogen concentration, and amino nitrogen concentration of protein, peptides, and amino acids, and then calculated the hydrolysis rate of proteins.
The variables of the conditions of hydrolysis process was achieved in this study with the following range value of tests parameter:
- Concentration of HCl solution ranged between 1-7 N,
- Hydrolysis temperature ranged between 35-95 °C, and
- The time of hydroly
In this study, nickel cobaltite (NC) nanoparticles were created using the sol-gel process and used as an adsorbent to adsorb methyl green dye (MG) from aqueous solutions. The adequate preparation of nickel cobaltite nanoparticles was verified using FT-IR, SEM, and X-ray diffraction (XRD) studies. The crystalline particle size of NC nanoparticles was 10.53 nm. The effects of a number of experimental variables, such as temperature, adsorbent dosage, and contact time, were examined. The optimal contact time and adsorbent dosage were 120 minutes and 4.5 mg/L, respectively. Four kinetic models—an intraparticle diffusion, a pseudo-first-order equation, a pseudo-second-order equation, and the Boyd equation—were employed to monitor the adsorpti
... Show More