Two-dimensional unsteady mixed convection in a porous cavity with heated bottom wall is numerically studied in the present paper. The forced flow conditions are imposed by providing a hydrostatic pressure head at the inlet port that is located at the bottom of one of the vertical side walls and an open vent at the top of the other vertical side wall. The Darcy model is adopted to model the fluid flow in the porous medium and the combination effects of hydrostatic pressure head and the heat flux quantity parameters are carefully investigated. These governing parameters are varied over wide ranges and their effect on the heat transfer characteristics is studied in detail. It is found that the time required to reach a desired temperature at the bottom wall decreases with heat flux and pressure head increase. The higher heat flux quantities leaves wider regions near the top wall at lower temperatures which is important in most engineering applications like drying.
Mixed Convection in a Square Cavity Filled with Porous
Medium with Heated Bottom Wall
Porous Medium
Mixed Convection
Square Cavity
Uniform
Heating
Finite Volume Method
Publication Date
Wed Apr 25 2018
Journal Name
Ibn Al-haitham Journal For Pure And Applied Sciences
Different Estimation Methods for System Reliability Multi-Components model: Exponentiated Weibull Distribution
Exponentiated Weibull Distribution (EWD)
Reliability of multi-component Stress – Strength models R(s
k)
Maximum likelihood estimator (MLE)
Moment estimator (MOM)
shrinkage method (Sh)
Least Squares Estimator (LS)
Rank Set Sampling (RSS). and mean squared error (MSE).
In this paper, estimation of system reliability of the multi-components in stress-strength model R(s,k) is considered, when the stress and strength are independent random variables and follows the Exponentiated Weibull Distribution (EWD) with known first shape parameter θ and, the second shape parameter α is unknown using different estimation methods. Comparisons among the proposed estimators through Monte Carlo simulation technique were made depend on mean squared error (MSE) criteria
(1)
Publication Date
Mon Apr 06 2020
Journal Name
August
INFLUENCE OF SOME FACTOR ON SOMATIC EMBRYOS INDUCTION
AND GERMINATION OF DATE PALM CV BARHI BY USING CELL
SUSPENSION CULTURE TECHNIQUE
This study was done to examine different concentrations of mercuric chloride (Hgcl2) for Explants sterilization and different
concentration of NAA) mg/L with 2iP for their effect on initiation primary callus and subsequent embryogenesis in Phoenix
dactyliferae cultivar Barhi. Leaf primordial and shoot tips were excised from 2-3 years old offshoot. The result showed that
contamination percentage decreased with an increase in concentration of Hgcl2 for two explants where in the control (0.0)%
gave highest value 75% and 62.5% of contamination for leaf primordial and shoot tip respectively while the addition (0.1)%
gave a significant decrease 37.5 and 0% for explants respectively. The Explants were inoculated onto Murashiege and Skoog
1962 (MS) medium supplemented with 2iP 3mg/L and containing 0
25
50 or 100 mg/L of NAA
the addition (50) mg/L of NAA
gave highest value 68.8% in percentage of callus initiation with significant difference from addition 0% gave lowest value
(18.8)%
as well Explants of shoot tip gave significant difference was 53.1% while leaf primordial gave 28.1%
Primary callus
was transferred to fresh MS medium containing (0
5
10 and 20) mg/L of NAA with 3mg/L 2iP
Results were recorded after 12
weeks. A highest value of embryonic callus induction percentage or fresh weight and dry weight 87.5% or 1.56g and 0.47g for
the character respectively for the treat 20 mg/L while control treatment 0.0 gave the lowest value 12.5% or 0.37g and 0.14g for
same character respectively. Inoculated 1g fresh biomass into a 250 ml Erlenmeyer flask containing 50 ml MS liquid medium
supplemented with NAA 20mg/L and agitated at 150 rpm by shaker to making suspension culture the measurements of
packed cell volume ( pcv) or fresh and dry weight taken weekly for 12 weeks
maximum values were reached in the eighth week
of PCV and fresh weight but the dry weight reached to highest value in seventh week
then the curve began to decline
gradually until it reached stability in the last two weeks. The cell suspension was Diluted to different initial cell density of 100
500
10000
50000 and 100000 cells /ml with hemocytometer. The initial cell number of (10000) cells gave significant different
of plating efficiency PE (11.6)% while (100) cells gave lowest value 1.8% of PE.
Publication Date
Tue Dec 31 2019
Journal Name
Journal Of Economics And Administrative Sciences
Comparing Different Estimators for the shape Parameter and the Reliability function of Kumaraswamy Distribution
Kumaraswamy distribution
the shape parameter
reliability function
maximum likelihood
Bayes method
prior distributions (exponential distribution
chi-squared distribution and Erlang-2 type distribution)
the squared error loss function.
توزيع Kumaraswamy
معلمة الشكل
دالة المعولية
الإمكان الاعظم
طريقة بيز
التوزيعات الأولية (التوزيع الاسي
توزيع مربع كاي
توزيع ارلنك)
دالة الخسارة التربيعية.
In this paper, we used maximum likelihood method and the Bayesian method to estimate the shape parameter (θ), and reliability function (R(t)) of the Kumaraswamy distribution with two parameters l , θ (under assuming the exponential distribution, Chi-squared distribution and Erlang-2 type distribution as prior distributions), in addition to that we used method of moments for estimating the parameters of the prior distributions. Bayes
Publication Date
Sat Oct 01 2022
Journal Name
Environmental Advances
Stability and performance studies of emulsion liquid membrane on pesticides removal using mixture of Fe3O4Â nanoparticles and span80
The current study investigated the impact of nonionic surfactant span 80 in the existence of Fe3O4 magnetic nanoparticles on the emulsification of mixture of kerosene as petroleum based organic solvents and corn oil as a green diluent in the ratio 1:1
HCl was used as internal phase and the stability of the emulsion was carried out. The proposed Pickering emulsion liquid membrane has been exploited to investigate it is ability in the extraction of Abamectin pesticides from aqueous solution without utilizing carrier agent. Further
the effects of experimental parameters on extraction efficiency and emulsion stability such as
homogenizer speed
emulsification speed
contact time
Fe3O4-Span 80 ratios
HCL concentration
internal to membrane volume ratio (I/O) and pH of the external feed solution were carried out. The results showed that more than 99% of Abamectin could be extracted at 10 min contact time with a minimum breakage percent of 0.52% at the optimal conditions. The kinetic of the extraction were studied and the mass transfer coefficient was found to be for external phase () of 1.2
interfacial reaction rate constant () of 5.83 and the overall mass transfer coefficient () of 3.91 . The results of recyclability of the PELM revealed that the emulsion stability and extraction efficiency was nearly unchanged after three cycles.
(14)
(10)
Publication Date
Wed Jan 01 2020
Journal Name
Technologies And Materials For Renewable Energy, Environment And Sustainability: Tmrees20
Change detection of the land cover for three decades using remote sensing data and geographic information system
The changes in the land cover using geographical information systems and remote sensing techniques for the period (1990 - 2019) for part of the Baghdad governorate in central Iraq are detected and monitored. In this research
four satellite scenes with different sensors were used the TM
ETM+
and OLI
which were obtained by Landsat-5
Landsat-7 and Landsat-8 satellites
respectively. Maximum likelihood method supervised classification is adopted as the main classifier to distinguish different land cover types in the study region. The results showed that there are ten different classes in the values of their reflectance. This study proved that any landcover of the earth’s surface can be studied and determined by its spectral characteristics. The change for each class of the land cover for the study area was determined within the study period. The results of the study confirmed the possibility of identifying the types of land cover and finding the percentage of changes that occur in it and detecting it with high efficiency using the remote sensing technique.
(3)
Publication Date
Sat Sep 01 2018
Journal Name
Polyhedron
Novel dichloro (bis {2-[1-(4-methylphenyl)-1H-1, 2, 3-triazol-4-yl-κN3] pyridine-κN}) metal (II) coordination compounds of seven transition metals (Mn, Fe, Co, Ni, Cu, Zn and Cd)
The 1
3-dipolar cycloaddition “click” reaction between an azide and an alkyne to give a 1
2
3-triazole was reported by Huisgen in 1961 [1]. In 2002 the Copper(I)-catalyzed Azide-Alkyne Cycloaddition (CuAAC) to prepare a 1
2
3-triazole was reported [2]
[3]. The existence of relatively basic nitrogen atoms in the 1
2
3-triazole rings
and the possibility of introducing additional donor groups in the substituents (Fig. 1)
made the CuAAC “click” reaction an attractive method to prepare differently substituted 1
2
3-triazoles. These compounds have been used as ligands to coordinate to various metal ions that display a range of applications such as in electrochemical and photochemical studies
in supramolecular chemistry
magnetism
metal-ion sensing and catalysis [4]. The reasons for the success of the “click” reaction
is that it is easy to carry out and is widely applicable. It is not affected by a variety of functional groups
and can be carried out with a variety of Cu(I) catalysts and solvents
including aqueous conditions. The Cu(I) catalysts overcome the high activation energy barrier of the non-catalyzed Huisgen reaction by changing the mechanism of the reaction. A large variety of copper catalysts can be used for the CuAAC reaction
on condition that the maximum concentration of Cu(I) species is generated during the reaction. The pre-catalyst can be a Cu(II) salt (usually CuSO4) together with a reducing agent (often sodium ascorbate) or a Cu(I) compound in the presence of a base or amine ligand and a reducing agent to prevent oxidation to Cu(II). Some strong oxidising cupric salts or complexes such as Cu(OAc)2 also work. The solvent is very flexible from organic to aqueous
with the most commonly used combination water + an alcohol (t-BuOH
MeOH or EtOH). The key role of the solvent or solvent mixture is to solubilize the substrates and Cu(I) catalyst in order to ensure rapid reactions. Such aqueous conditions are very useful for biochemical conjugations
as well as for organic syntheses.
We recently reported on the synthesis of a series of differently substituted 1
2
3-triazole chromophores
the substituted 2-(1-phenyl-1H-1
2
3-triazol-4-yl)pyridine ligands [5]
see Fig. 2 middle
with substituents R = H (L1)
CH3 (L2)
OCH3 (L3)
COOH
F
Cl
CN
CF3
O(CH2)3CH3 and N(CH3)2. These versatile ligands were found to coordinate to various first row transition metals
such as manganese
cobalt and nickel [6]. Here we extend the series to include more first row transition metal(II) coordination compounds
iron
copper and zinc
as well as a second row transition metal(II) coordination compound
cadmium
containing the 2-(1-(4-methyl-phenyl)-1H-1
2
3-triazol-1-yl)pyridine chromophore (Fig. 2 right with R = CH3). This series of seven novel coordination compounds is the first series of pyridyl-triazole based transition metal coordination compounds where seven different transition metals are coordinated to the same 1
2
3-triazole chromophore
namely 2-(1-(4-methyl-phenyl)-1H-1
2
3-triazol-1-yl)pyridine.