Background: Water-pipe can be defined as a single or multi stemmed device that used to vaporize and smoke flavored tobacco whose smoke is passed via water vase before inhalation. Water-pipe smokers are at risk of exposure to many toxic chemicals that are not filtered by water, as well as risk of infectious diseases when the mouth piece of the water-pipe is shared. This study was carried out to investigate the effect of water pipe on the oral health. Materials and Methods: Sixty persons were included in this study aged between 22 and 23 years. Forty persons were coffee shop workers for at least five years, half of them were water-pipe smokers (active smokers) and the other weren’t smokers (passive smoker), the last group was the co

Background: There are so many evidences that there was antimicrobial resistance, and there were many strains that emerged which were difficult to treat. We are living in a situation that the dissemination of multiple drug resistant bacteria can lead us to the situation, in which no treatment could be offered for bacterial infection in future.

Aim of study: Assessment of nurses’ knowledge, attitude, and practices on antibiotic use and resistance in Fatima Al Zahra hospital in Baghdad.

Subjects and Methods:  A cross-sectional study. The study was carried on from 1st of February to 31st of March 2021.  A questionnaire was constructed by the research team based on literature review and was adapted to asses

The aim of this research is to study the effect of welded joint design (Butt joint and lap joint) on thejoint strength during tension and fatigue loading with different current of welding (40,50,60,70,80) ^per, and different type of wire welding. The result of this research is showed that the effect of fatigue loading on the type of joint is more than the effect of tension loading on it. And the butt joint welding is better than the lap joint welding during the fatigue loaded.The experimental results of the effect of W'elding current showed that more increasing and more decreasing the value of the heat input, during the welding was found to produce mechanical brittleness on the buttjoint welding during the static and dynamic loading. Also i

Background: Investigating dental health knowledge among children is important. Knowing what behaviors are right in relation to dental health does not guarantee that children will practice those behaviors. However, lack of knowledge and misconceptions about dental health may lead to behaviors that are harmful to teeth and gum. Baseline data on knowledge levels are required to determine which particular areas of dental health education are in need of improvement for high-risk children living in different geographical areas. This research was conducted to study the oral health status, dental knowledge and behavior in relation to two different cities, among children in Baghdad and Thamar (republic of Yemen) governorate. Materia

 This research deal the primary and secondary sedimentary structures in the By Hassan Formation in the three locations in the northeast of Iraq.          Can be recognize many geological structures such as cross bedding, planer bedding, graded bedding, channel structure and mud ball house deposit in the flood plain. The ether side this research study the direction of old current and sedimentary structure that made by the one direction current

In this work, the effect of annealing temperature on the electrical properties are studied of p-Se/ n-Si solar cell, which p-Se are deposit by DC planar magnetron sputtering technique on crystal silicon. The chamber was pumped down to 2×10−5 mbar before admitting the gas in. The gas was Ar. The sputtering pressure varied within the range of 4x10-1 - 8x10-2mbar by adjusting the pumping speed through the opening control of throttle valve. The electrical properties are included the C-V and I-V measurements. From C-V measurements, the Vbi are calculated while from I-V measurements, the efficiency of solar cell is calculated.

This research presents a particular designing strategy for a free form of surfaces, constructed by the lofting design method. The regarded surfaces were created by sliding a B-spline curves (profile curves), in addition to describing an automatic procedure for selective identification of sampling points in reverse engineering applications using Coordinate Measurement Machine. Two models have been implemented from (Ureol material) to represent the different cases of B-spline types to clarify its scope of application. The interior data of the desired surfaces was designed by MATLAB software, which then were transformed to UG-NX9 software for connecting the sections that were designed in MATLAB program and obtaining G-code programs for the