The high bounce activity according to the fosbery way is regarded as of the difficult sports concerning its way of training and perfection due to hard technique of its performance on one hand and because it depends on the player’s ability to overcome body weight resistance against the gravity. In addition to the strong ability to control the body posture when leaving the land and flying over the barrier. This activity needs to high plosion power at the moment of bouncing and this plosion depends on the period of bouncing, so the two researchers aimed to use a mechanical bouncing platform and an electronic one through several training by one foot and both feet in different directions and positions in order to reduce the time of bouncing and increase the plosion power. So the study aims to identify the influence of the jumping trainings on a bouncing platform to improve the time of bouncing and the plosion power of the players under the age of 18. The experimental approach has been used to design the group of trainings pertaining and post training. The sample of the study is four players that have been selected from Al Hilla club for high bouncing. All of them are under the age of 18 and they represent the society for 100%. The post evaluation for the bouncing time and the plosion power by using the platform as it is for evaluation and training. After that, the training has started on the platform by the sample in 15/3/2021 to 9/5/2021 two times a week. The training has been accomplished on the designed platform at the main part of training lesson directly after warming up and for twenty minutes. The training was performed depending on the principle of gradiance and ripple among the trainings, units and the weeks of training period. The replacement of the muscular groups have been used between one training and another by using the high periodic training and the two researchers have not interrupted in the rest of the parts of the training . After the training finished. The post tests have been perrformed and the results have been calculated statistically by using SPSS and the study reached to that the training on the bouncing back platform reduced the time of bouncing and increased the plosion power for the high bouncing players under the age of 18 and this is a positive index to reach better height over the barrier. So it is recommended to perform the high bouncing training on a bouncing platform in order to improve the time of bouncing and the power of plosion for the high bouncing players under the age of 18 .
The study aims to identify the impact of electronic games on increasing the dropout rate among students in the basic stage in Jordan from their teachers’ point of view. The study adopted a descriptive survey method. Its community consisted of all fe(male) teachers of the basic stage in public and private schools, (First Amman, Irbid, and special education in Zarqa and Amman). The electronic questionnaire was used as a tool for the study. The results have shown that the effect of electronic games on increasing the dropout rate among students in the basic stage in Jordan was high. Besides, there are statistically significant differences due to the gender variable for males. There are statistically significant differences due to the varia
... Show More
In this paper, customers’ expectations are continually shifting due to the business environment’s growing competition and substantial changes. As a result, organisations no longer viewed it as a static objective but as an ever-evolving aim. From this vantage point, the research has explored the accounting literature in search of novel approaches to addressing the strategic dimensions of quality, cost and time. Getting them to respond positively to the customer’s requests also requires recognising their needs and controlling their impact on these dimensions. With the removal of operations that do not contribute any value to the product’s value chain and a reduction in manufacturing costs through continuous improvement, the ou
... Show More
(37)
(7)
The effect of solution heat treatment on the mechanical properties of Aluminum-Copper alloy. (2024-T3) by the rolling process is investigated. The solution heat treatment was implemented by heating the sheets to 480 C° and quenching them by water; then forming by rolling for many passes. And then natural aging is done for one month. Mechanical properties (tensile strength and hardness) are evaluated and the results are compared with the metal without treatment during the rolling process. ANSYS analysis is used to show the stresses distribution in the sheet during the rolling process. It has been seen that good mechanical properties are evident in the alloy without heat treatment due to the strain hardening and also the mechanical
... Show MoreThe effect of fiber volume fraction of the carbon fiber on the thermal conductivity of the polymer composite material was studied. Different percentages of carbon fibers were used (5%, 10%, 15%, 20%, and 25%). Specimens were made in two groups for unsaturated polyester as a matrix and carbon fibers, first group has parallel arrangement of fibers and the second group has perpendicular arrangement of fibers on the thermal flow, Lee's disk method was used for testing the specimens. This study showed that the values of the of thermal conductivity of the specimens when the fibers arranged in parallel direction was higher than that when the fibers arranged in the perpendicular direction
 
... Show MoreCarbides or nitrides thin films present materials with good mechanical properties for industrial applications as they can be coatings at low temperatures serve temperature sensitive surfaces. In this work the effect of the C percentage on the mechanical properties represented by the Young modulus (E) of combinatorial magnetron sputtered TiCx (34%x˂65%) has been studied. The structure of the produced films is TiC independent on the C concentration. The mechanical properties are increased with increasing the C concentration up to 50%, and then decreasing with further C % increasing. These results can be explained by considering the resultant residual stresses.
Porous silicon (PS) layers were formed on n-type silicon (Si) wafers using Photo- electrochemical Etching technique (PEC) was used to produce porous silicon for n-type with orientation of (111). The effects of current density were investigated at: (10, 20, 30, 40, and50) mA/cm2 with etching time: 10min. X-ray diffraction studies showed distinct variations between the fresh silicon surface and the synthesized porous silicon. The maximum crystal size of Porous Silicon is (33.9nm) and minimum is (2.6nm) The Atomic force microscopy (AFM) analysis and Field Emission Scanning Electron Microscope (FESEM) were used to study the morphology of porous silicon layer. AFM results showed that root mean square (RMS) of roughness and the grain size of p
... Show More
The paper include study the effect thickness of the polymeric sample which is manufactured by thermo press way. The sample was used as an active tunable R6G laser media. The remarks show that, when the thickness of the samples is increased, with the same concentration, the spectrum will shift towards the short wavelength, & the quantum fluorescence yield will increased. The best result we obtained for the quantum fluorescence yield is (0.68) at the sample, with thickness (0.304mm) in Ethanol solvent, while when we used the Pure Water as a solvent, we found that the best quantum fluorescence yield is (0.63) at (0.18mm) thickness of the sample.
The physical, the thermal and the mechanical properties of Nano-composites, that consisted of Polyprime EP epoxy that reinforced by multi-walled carbon nanotubes (MWCNTs), have been studied. Various loading ratios, 0.1, 0.5, and 1 wt. %of MWCNT shave been infused into epoxy by a magnetic stirrer and then the hardener mixed with the mthat supplied with the epoxy. All sample shave been cutting using CNC machine. Tensile test, three-point bending, hardness tests, lee's disk, differential scanning calorimetry, water absorption and dielectric and electrical conductivity test were utilized on unfilled, MWCNT-filled epoxy to identify the loading effect on the properties of materials. Scanning electron microscopy (SEM) was used to determine the
... Show More
Cadmium sulfide and Aluminum doped CdS thin films were prepared by thermal evaporation technique in vacuum on a heated glass substrates at 373K. A comparison between the optical properties of the pure and doped films was made through measuring and analyzing the transmittance curves, and the effect of the annealing temperature on these properties were estimated. All the films were found to exhibit high transmittance in the visible/ near infrared region from 500nm to 1100nm.The optical band gap energy was found to be in the range 2.68-2.60 eV and 2.65-2.44 eV for CdS and CdS:Al respectively , with changing the annealing temperature from room temperature to 423K.Optical constants such as refractive index, extinction coefficient, and complex di
... Show More